Venting Requirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE™ vent products are recommended.

DURASAFE™ vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the “Assistance or Service” section of this manual.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

Do not use an exhaust hood with a magnetic latch.

Do not install flexible metal vent in enclosed walls, ceilings or floors.

Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws or other fastening devices which extend into the interior of the duct. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow.

An exhaust hood should cap the vent to prevent rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or flexible metal vent.

Plan Vent System

Typical installations vent the dryer from the rear of the dryer.

A

B

C

A. Exhaust hood

B. Flexible metal vent or rigid metal vent

C. Elbow

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions provided with the vent system.

AB

A. Over-The-Top installation (also available with one offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. For ordering information see “Assistance or Service.”

Over-The-Top Installation: Part Number 4396028

Periscope Installation (for use with dryer vent to wall vent mismatch):

Part Number 4396037 - for mismatch of 0" (0 cm) to 18" (45.72 cm)

Part Number 4396011 - for mismatch of 18" (45.72 cm) to 29" (73.66 cm)

Part Number 4396014 - for mismatch of 29" (73.66 cm) to 50" (127 cm)

6

Page 6
Image 6
Whirlpool 8578198 manual Venting Requirements, Plan Vent System, Alternate installations for close clearances

8578198 specifications

The Whirlpool 8578198 is a high-quality range appliance designed to elevate the cooking experience in any kitchen. Known primarily as a cooking element, this part is made specifically for various Whirlpool models, ensuring compatibility and reliability. One of its standout features is the high-performance heating element that guarantees even cooking results, making it easier to prepare meals to perfection.

This component is designed with user convenience in mind. Its powerful output ensures rapid heating, significantly reducing the time needed to bring pots to boiling temperatures or to sear meats. Combined with a consistent and stable temperature, it allows for precision cooking, which is essential for recipes that require strict temperature control. This ability to maintain heat effectively leads to improved cooking accuracy and can prevent overcooking or undercooking, which is particularly important for delicate dishes.

In addition to its heating efficiency, the Whirlpool 8578198 is also crafted for durability. Made from robust materials that withstand high temperatures and heavy use, this component promises long-lasting performance. The thoughtful engineering behind the design minimizes the risk of wear and tear, thus reducing the need for frequent replacements, which can be both costly and inconvenient.

The Whirlpool 8578198 also features easy installation, making it a suitable choice for both professional repair technicians and DIY enthusiasts. The straightforward design allows users to replace their old or malfunctioning heating elements without needing specialized tools or extensive mechanical knowledge.

When it comes to safety, Whirlpool has prioritized user protection in the design of the 8578198. The part includes safety features that protect against overheating and short-circuiting, ensuring peace of mind while cooking. In addition, it is tested rigorously to meet various safety standards set by regulatory bodies.

In summary, the Whirlpool 8578198 heating element combines efficiency, durability, and safety, making it an essential component for anyone seeking to enhance their kitchen experience. With its ability to provide even heating and support precision cooking, it stands out as a reliable choice for transforming home cooking into a professional-like experience. Whether you are a novice or an experienced chef, this appliance is designed to meet a variety of culinary needs and elevate your overall cooking performance.