Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Dryer Dimensions

36"

(91.4 cm)

*28.65" (72.77 cm)

50¹⁄₂"

(128.27 cm)

27"

Failure to do so can result in death, explosion, or fire.

You will need

(68.6 cm)

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”

A location that allows for proper exhaust installation. See “Venting Requirements.”

A separate 30-amp circuit.

A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

A sturdy floor to support the total dryer weight of 127 lbs (57.6 kg). The combined weight of a companion appliance should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (If slope is greater than 1" [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.

For a garage installation, you will need to place the dryer at least 18" (46 cm) above the floor. If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Companion appliance spacing should also be considered.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation clearances

The location must be large enough to allow the dryer door to open fully.

Custom undercounter installation - Dryer only

36" min

 

 

(91.4 cm)

 

 

1"*

27"

1"*

(2.5 cm)

(68.6 cm)

(2.5 cm)

*Required spacing

2"* (5 cm)

5

Page 5
Image 5
Whirlpool 8578901 manual Location Requirements, Dryer Dimensions, You will need, Installation clearances

8578901 specifications

The Whirlpool 8578901 is a vital component in many households as a replacement part designed for Whirlpool washing machines. This specific part is known for its reliability and compatibility with various Whirlpool models, making it a sought-after choice for homeowners seeking to maintain the efficiency and performance of their washing appliances.

One of the primary features of the Whirlpool 8578901 is its robust construction. It is made from high-quality materials that ensure durability and long-lasting use. This means users can expect consistent performance over time without worrying about premature wear and tear. The component is designed to endure the rigorous demands of regular laundry use, providing peace of mind to consumers who rely on their washers for daily cleaning needs.

In terms of technology, the Whirlpool 8578901 incorporates advanced engineering that enables it to perform effectively within the washing machine's system. The part features a precise design that ensures seamless integration with other machine components. This compatibility helps to maintain optimal performance levels, preventing issues such as leaks or malfunctions that can disrupt laundry routines.

Another characteristic that stands out is the ease of installation. The Whirlpool 8578901 is designed for straightforward replacement processes, allowing users to easily replace worn-out or damaged parts without the need for professional assistance. This feature not only saves on repair costs but also empowers homeowners to take control of their appliance maintenance.

Additionally, the Whirlpool 8578901 offers excellent efficiency. By ensuring that the washing machine operates at its best, this part can contribute to lower energy consumption and water usage. Users can enjoy the benefits of a cleaner wash without incurring high utility bills, making it an environmentally friendly choice.

Moreover, the versatility of the Whirlpool 8578901 is noteworthy. It is compatible with multiple models, which expands its usability across a wide range of Whirlpool washing machines. This universality makes it an ideal solution for many consumers looking to maintain their appliances without needing to search for model-specific parts.

In summary, the Whirlpool 8578901 is a formidable replacement part characterized by its durability, advanced technology, ease of installation, efficiency, and versatility. For anyone looking to ensure their Whirlpool washing machine continues to operate optimally, investing in this part is a wise choice that reflects both practicality and quality.