TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate |
| Oven indicator lights flash |
■Is the power supply cord unplugged? Plug into a grounded outlet.
■Has a household fuse blown, or has a circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.
Cooktop will not operate
■Is the control knob set correctly? Push in knob before turning to a setting.
■On ceramic glass models, is the “Control Lockout” or “Lockout” set?
See “Control Lockout or Lockout” section.
Excessive heat around cookware on cooktop
■Is the cookware the proper size?
Use cookware about the same size as the surface cooking area, element or surface burner. Cookware should not extend more than ½" (1.3 cm) outside the cooking area.
Hot Surface indicator light stays on
■Does the Hot Surface indicator light stay on after control knob(s) have been turned off?
See “Cooktop Controls” section.
Cooktop cooking results not what expected
■Is the proper cookware being used? See “Cookware” section.
■Is the control knob set to the proper heat level? See “Cooktop Controls” section.
■Is the appliance level?
Level the appliance. See the Installation Instructions.
Oven will not operate
■Is the electronic oven control set correctly? See “Electronic Oven Control” section.
■Has a delay start been set? See “Timed Cooking” section.
■On some models, is the “Control Lockout” or “Lockout” set?
See “Control Lockout or Lockout” section.
Oven temperature too high or too low
■Does the oven temperature calibration need adjustment? See “Oven Temperature Control” section.
■On some models, does the cooling fan run during BAKE, BROIL or CLEAN?
It is normal for the fan to automatically run when the oven is in use. This helps cool the electronic control.
■Do the oven indicator lights flash?
See the “Display” and/or the “Oven Indicator Lights” section. If the indicator light(s) keeps flashing, call for service. See “Assistance or Service” section.
Display shows messages
■Is the display showing “PF” or flashing a time? There has been a power failure. Clear the display. See “Display(s)” section. On some models, reset the clock, if needed. See “Clock” section.
■Is the display showing a letter followed by a number? Depending on your model, press OFF/CANCEL, OFF or CANCEL/OFF to clear the display. See “Display(s)” section. If it reappears, call for service. See “Assistance or Service” section.
Self-Cleaning cycle will not operate
■Is the oven door open?
Close the oven door all the way.
■Has the function been entered? See
■On some models, has a delay start
See
■Has a delay start been set? See “Timed Cooking” section.
Oven cooking results not what expected
■Is the appliance level?
Level the appliance. See the Installation Instructions.
■Is the proper temperature set?
■Is the proper oven temperature calibration set? See “Oven Temperature Control” section.
■Was the oven preheated?
See the “Baking and Roasting” and “Broiling” sections.
■Is the proper bakeware being used? See “Bakeware” section.
■Are the racks positioned properly?
See “Positioning Racks and Bakeware” section.
■Is there proper air circulation around bakeware? See “Positioning Racks and Bakeware” section.
■Is the batter evenly distributed in the pan? Make sure batter is level in the pan.
■Is the proper length of time being used? Adjust cooking time.
■Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer cooking times.
■Are baked items too brown on the bottom? Move rack to higher position in the oven.
■Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or reduce baking temperature.
30
