Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

■

Flat-blade screwdriver

■

¹⁄₄" Drill bit

■

⁷⁄₁₆" and ¹⁄₂" Open-end or two

■

Hand drill or electric drill

 

adjustable wrenches

 

(properly grounded)

■¹⁄₄" nut driver

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

■All installations must meet local plumbing code requirements.

■Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 to 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber.

ConnecttheWater Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ¹⁄₂" (12.70 mm) to 1¹⁄₄" (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a grounded drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

8.Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1.Unplug refrigerator or disconnect power.

2.Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.

3.If the gray water tube supplied with the refrigerator is not long enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water supply line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A

B

C

D

E F G

A. Refrigerator water tubing

 

E. Ferrule (purchased)

B. Nut (provided)

 

 

F. Nut (purchased)

C. Bulb

 

 

 

G. Household water line

D. Coupling (provided)

 

 

 

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.

4

Page 3 Page 5
Page 4
Image 4
Whirlpool GD5NHAXSB00 Water Supply Requirements, ConnecttheWater Supply, Reverse Osmosis Water Supply, Style, Tools Needed
Page 3 Page 5

GD5NHAXSB00 specifications

The Whirlpool GD5NHAXSB00 is a standout refrigerator designed to meet the demands of modern households while providing ample storage, efficient cooling, and user-friendly features. With its sleek stainless steel finish and streamlined design, it not only complements your kitchen aesthetics but also enhances functionality.

One of the main features of the GD5NHAXSB00 is its generous capacity. with a total storage space of about 25 cubic feet. This refrigerator includes both a top freezer and a bottom refrigerator compartment, allowing for easy access to items you use most frequently. The fridge section is equipped with adjustable shelves, deli drawers, and door bins, providing customizable storage solutions for food of all shapes and sizes.

This model incorporates Whirlpool’s Accu-Chill temperature management system. This technology helps maintain a consistent and ideal temperature throughout the fridge and freezer, ensuring that your food stays fresher for longer. The intuitive controls make it simple for users to adjust settings and monitor temperature levels.

Another key characteristic of the GD5NHAXSB00 is the ENERGY STAR certification, which signifies that it meets strict energy efficiency guidelines set by the EPA. This means that consumers can save on energy costs while minimizing their environmental impact. Additionally, the refrigerator features an easy-to-use ice maker that provides a steady supply of fresh ice, perfect for entertaining or everyday use.

The cooling system utilizes a dual cooling technology, which separates the air in the refrigerator and freezer compartments to prevent odor transfer and optimize humidity levels. This ensures that fruits and vegetables retain their freshness and flavors without absorbing undesirable smells from other foods.

The exterior design includes ergonomic handles that make opening and closing the doors effortless, coupled with a fingerprint-resistant finish that helps maintain its pristine appearance. Furthermore, the integrated LED lighting brightens every corner, improving visibility and allowing easy navigation in low-light conditions.

In summary, the Whirlpool GD5NHAXSB00 refrigerator combines style, functionality, and advanced technology to create a reliable appliance for any kitchen. With its spacious layout, energy efficiency, and thoughtful design features, it is an excellent choice for families and individuals looking to elevate their food storage experience.
Top Page Image Contents