Remove the Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1.Unplug refrigerator or disconnect power.

2.Open both doors to 90°. Remove the base grille by removing the two screws, then pulling out on the outside corners. See Graphic 1.

NOTE: The doors must only be opened to 90°. If they are opened all the way, the base grille will not come off.

3.Disconnect the water tubing, located behind the base grille on the freezer door side. The dispenser tubing runs through the door hinge, and must be disconnected in order to remove the door.

■Style 1: Press the colored outer ring against the face of fitting and pull the water tubing free. See Graphic 2A.

NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that runs through the door hinge.

■Style 2: Firmly pull on the clasp to release the tube, then pull the water tubing free. See Graphic 2B.

NOTE: Keep the clasp attached to the tube that runs underneath the freezer.

4.Disconnect the wiring, located behind the base grille on the freezer door side. See Graphic 3.

■Remove the P-clamp using a ¹⁄₄" hex-head socket wrench. Remove the small wiring bundle from the P-clamp.

■Remove the wiring clip using a ¹⁄₄" hex-head socket wrench.

■Pull the electrical housing out from under the refrigerator. Disconnect the wiring plugs from the housing.

■Gently pull the large wiring bundle (with two white plugs) through the routing plate.

5.Close both doors and keep them closed until you are ready to lift them free from the cabinet.

6.Use a ³⁄₁₆" hex key to remove the top left hinge screws as shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

WARNING

Excessive Weight Hazard Use two or more people to lift the freezer door. Failure to do so can result in back or other injury.

7.Lift freezer door straight up off bottom hinge. See Graphic 5. The water tubing and wiring remain attached to the freezer door and pull through the bottom left hinge.

NOTE: This may require two people - one to lift the door and another to feed the water tubing and wiring through the hinge. Be sure the hole in the hinge is clear of obstructions, then gently pull one water tube through the hinge. (Avoid kinking the tube.) Next, gently pull the other water tube through the hinge, again avoiding kinks. Finally, gently pull the wiring bundle (including the grommet and wiring plugs) through the hinge.

IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door, water tubing and wiring.

8.Use a ³⁄₁₆" hex key to remove the top right hinge screws as shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

9.Lift the refrigerator door straight up off bottom hinge.

IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door.

10.It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges have similar construction.

■If necessary, use an internal star drive or a ³⁄₈" hex-head socket wrench to remove the bottom hinges. See Graphic 7.

IMPORTANT: The leveler brackets are mounted behind the hinges. If you remove the hinges, make sure that the leveler brackets are replaced when reinstalling the hinges.

Replace the Doors and Hinges

1.Replace both bottom hinges, if removed. Make sure that the leveler brackets are assembled behind the hinges. Tighten screws.

IMPORTANT: When the screws are tightened properly, there should not be any gaps between the refrigerator, leveler bracket and hinge.

NOTE: There are two wiring bundles that run underneath the freezer - a large bundle with a large grommet and two white plugs at the end, and a small bundle with a small grommet and one yellow plug at the end.

WARNING

Excessive Weight Hazard Use two or more people to lift the freezer door. Failure to do so can result in back or other injury.

2.Before replacing the freezer door on the bottom left hinge, feed the small wiring bundle through the hinge. Assistance may be needed.

IMPORTANT: Do not feed the large wiring bundle through the hinge. This bundle is intended to run directly from the door to the connections beneath the freezer. Forcing the large bundle through the hinge may damage the door and/or the wiring, and will keep the door from closing properly.

3.Feed both water tubes through the bottom left hinge, then replace the freezer door on the hinge. Assistance may be needed.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.

4.Align and replace the top left hinge as shown. See Graphic 4. Tighten screws.

5

Page 4 Page 6
Page 5
Image 5
Whirlpool GSS30C6EYY Remove the wiring clip using a ¹⁄₄ hex-head socket wrench, Replace the Doors and Hinges
Page 4 Page 6

GSS30C6EYY specifications

The Whirlpool GSS30C6EYY is a remarkably versatile and efficient side-by-side refrigerator that has earned its place in many homes due to its design and functionality. This model is particularly designed to cater to the needs of families looking for convenience without compromising on style.

One of the standout features of the Whirlpool GSS30C6EYY is its spacious interior. The refrigerator provides ample storage space, with a total capacity of approximately 30 cubic feet. It offers adjustable shelves that allow users to customize the layout to accommodate larger items, making organization effortless. Additionally, the side-by-side design allows easy access to both frozen and fresh food items, making meal preparation a breeze.

The cooling technology in the GSS30C6EYY is advanced. It employs efficient cooling systems that maintain uniform temperatures across its compartments. This ensures that food stays fresh longer, while the built-in humidity-controlled crisper drawers are perfect for fruits and vegetables, preserving their crispness and flavor.

Another important feature is the Ice and Water Dispenser located on the front of the refrigerator. This convenient addition offers filtered water and ice on demand, making it easy to stay hydrated while entertaining guests or during hot summer months. The dispenser is designed for ease of use, allowing one-handed operation which is a definite plus for busy households.

Energy efficiency is also a significant highlight of the Whirlpool GSS30C6EYY. This model is Energy Star certified, which means it meets strict energy efficiency guidelines set by the Environmental Protection Agency. This not only helps in reducing energy bills but also contributes positively to the environment, making it a wise choice for eco-conscious consumers.

The exterior design of the GSS30C6EYY is sleek and modern, available in a classic white finish that matches various kitchen aesthetics. The easy-to-clean surface is resistant to fingerprints, ensuring that the refrigerator looks pristine with minimal maintenance.

Overall, the Whirlpool GSS30C6EYY refrigerator combines style, functionality, and energy efficiency, making it an excellent choice for those searching for a reliable home appliance. With its spacious design, advanced cooling technology, convenient dispensers, and eco-friendly features, this refrigerator stands out as a dependable kitchen companion.
Top Page Image Contents