Undercounter Dishwasher
PRODUCT MODEL NUMBERS
GU3100XTV
Requirements:
●
●Copper wire only, 2 wire with ground
Recommended:
●
●Separate circuit
Direct Wire Connection:
●Use flexible, armored or nonmetalic sheathed, copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.
●Use strain relief method provided with house wiring junction box or install a
Power Supply Cord Connection:
Use Power Supply Cord Kit (Part Number 4317824) marked for use with dishwashers. Kit contents include:
●Voltex, Inc., UL listed 16 gauge
●Neer
●3 wire connectors
●Part Number 302797 grommet
Follow the kit instructions for installing the power supply cord.
NOTE: Power supply cord must plug into a mating three prong, grounded outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.
IMPORTANT: If you plan to install a garbage disposal, an additional separate
Water Supply Requirements:
●A hot water line with
●120°F (49°C) water temperature at dishwasher.
●³⁄₈" O.D. copper tubing with compression fitting or flexible braided water supply line.
NOTE: ¹⁄₂" minimum plastic tubing is not recommended.
●90º elbow with 3⁄8" N.P.T. external pipe threads on one end.
IMPORTANT: Do not solder within 6" (15.2 cm) from water inlet valve.
Drain Requirements:
●Use the new drain hose supplied with your dishwasher. NOTE: If a longer drain hose is required:
●Use a new drain hose with maximum length of 10 ft
(3 m) that meets all current AHAM/IAPMO test standards
●Use a new drain hose that is resistant to heat and detergent
●Use a new drain hose that fits the 1" (2.5 cm) drain connector on the dishwasher.
●Connect drain hose to waste tee or disposal inlet above drain trap in house plumbing.
●Connect drain hose to house plumbing 20" (50.8 cm) minimum above the floor.
NOTE: It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.
●Use a drain air gap if the drain hose is connected to house plumbing lower than 18" (45.7 cm) above the subfloor or floor.
Drain Air Gap:
●Use ¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.
NOTE: Do not connect drain lines from other devices to the dishwasher drain hose.
MINIMUM CLEARANCES
Check location where the dishwasher will be installed. the location must provide:
●Easy access to water, electricity and drain.
●Convenient access for loading and unloading dishes. Corner locations require 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.
●A minimum of 25⁵⁄₈" (65.1 cm) is required in front of the dishwasher to allow the door to open fully.
C
B
AD
A. 2" (5.1 cm) minimum clearance | C. Countertop |
for door opening | D. 25⁵⁄₈" (65.1 cm) minimum |
B.Dishwasher
●Square opening for proper orientation.
●Cabinet front perpendicular to floor.
●Level floor. If the floor at the front of the dishwasher is not level with the rear of the opening, shims may be needed to level the dishwasher.
NOTE: To avoid shifting during dishwasher operation, shims must be securely attached attached to the
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation | Ref. |
Instructions packed with product. Specifications subject to change without notice. |
