Whirlpool RT21LMXJW00 manual Adjustable Half-width Freezer Shelf, Pull-out Freezer Floor

NOTE: The ice maker will not make ice until the freezer is cold enough. Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

To turn the ice maker off:

■Automatic turn off: As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position.

■Manual turn off: Lift the wire shut-off arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

To increase ice production rate:

■Maximum Ice Production (on some models): In maximum ice production, the ice maker should produce approximately 16 to 20 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.

■Normal Ice Production: In normal ice production mode, the ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn the Freezer Control to the highest setting, waiting 24 hours between each increase.

REMEMBER:

■Allow 24 hours to produce the first batch of ice.

■Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker.

■Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■It is normal for the ice cubes to be attached at the corners. They will break apart easily.

■Do not force the wire shut-off arm up or down.

■Do not store anything on top of the ice maker or in the ice storage bin.

Freezer Shelf

(on some models)

To remove the shelf:

1.Lift entire shelf slightly.

2.Move shelf all the way to one side.

3.Tilt other side up and out of shelf supports.

4.Pull shelf up and out

To replace the shelf:

1.Tilt the shelf and insert into freezer compartment.

2.Insert one end of the shelf all the way into the center of the shelf supports.

3.Lower other end of shelf and insert into the shelf supports.

4.Lower shelf into place.

NOTE: The shelf should lower slightly and lock into place. If the shelf does not appear stable, make sure both ends of the shelf are inserted into the shelf supports.

Frozen food storage guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Seal the package or container securely to prevent taste and odor transfer throughout the product. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2-3 lb of food per cubic foot [907-1,350 g per L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.

NOTE: For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

Adjustable Half-width

Freezer Shelf

(on some models)

To remove and replace the shelf:

1.Remove the shelf by lifting the shelf up and pulling straight out.

2.Replace the shelf over the supports and lower it into place.

Pull-out Freezer Floor

(on some models)

To remove and replace the freezer floor:

1.Lift both back “fences” up and out.

2.Remove the freezer floor by pulling it out about 1 in (25.40 mm) with one hand around the air tower section (center back) and one hand at center front.

3.Lift up floor at rear until hooks release from cabinet and pull the floor out the rest of the way.

4.Replace the freezer floor by sliding the floor straight in until the hooks drop into place at rear of cabinet.

5.Replace “fences” by aligning pins with socket in the floor, and pushing down until they snap into place.

14