4.Replace the burner cap, making sure the alignment pins are properly aligned with the burner cap.
A
B
A.Incorrect
B.Correct
5.Turn on the burner. If the burner does not light, check cap alignment. If the burner still does not light, do not service the sealed burner yourself. Contact a trained repair specialist.
GriddleGrate
(onsomemodels)
IMPORTANT: Do not use the griddle grate while using the Self- Clean mode.
A
A. Griddle grate installed on right side of cooktop
To Use the Griddle Grate:
1.Remove the right side grate from the cooktop and replace it with the griddle grate.
2.Before each use, brush on a thin layer of cooking oil to keep food from sticking. Cooking sprays may leave a sticky residue on the griddle that is hard to remove.
3.Preheat the griddle for 5 minutes. Preheating the griddle slowly will ensure even heat distribution and will avoid warping the griddle.
4.For preheating and cooking, set the front burner to the lowest heat setting and the rear burner to medium or medium high heat for best performance.
To Clean the Griddle Grate:
1.Let the griddle cool, then empty the grease tray.
2.See the “General Cleaning” section for cleaning instructions.
3.Store griddle in a cool dry place.
OVEN USE
Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well- ventilated room.
Electronic OvenControls
Control Display
The display will flash when powered up or after a power loss. Press CANCEL/OFF to clear. When oven is not in use, the time of day is displayed. Indicator lights show functions that are in use.
Tones
Tones are audible signals, indicating the following:
One tone
■Valid pad press
■Oven is preheated (long tone)
■Function has been entered
■Reminder (on some models), repeating each minute after the
Three tones
■Invalid pad press
Four tones
■End of cycle
To Change Tone Settings:
Tone Pitch
Sets the pitch of the tone to either high or low.
Press and hold BROIL for 5 seconds. “TONE PITCH HIGH” or “TONE PITCH LOW” will appear in the display. Press and hold BROIL again to change setting.
To exit, press CANCEL/OFF.
Key Press Tones
Activates or turns off the tones when a keypad is pressed.
Press and hold KEEP WARM for 5 seconds. “KEY PRESS TONES ON” or “KEY PRESS TONES OFF” will appear in the display. Press and hold KEEP WARM again to change setting.
To exit, press CANCEL/OFF.
End of Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
Press and hold CONVECT for 5 seconds. “CYCLE END TONE ON” or “CYCLE END TONE OFF” will appear in the display. Press and hold CONVECT again to change setting.
To exit, press CANCEL/OFF.
Reminder Tones Disable
Turns off the short tones that sound 1 minute after the end of cycle tones.
Press and hold BAKE for 5 seconds. “REMINDER TONES ON” or “REMINDER TONES OFF” will appear in the display. Press and hold BAKE again to change setting.
To exit, press CANCEL/OFF.
Audible Tones Disable
Turns off all tones, including the end of cycle tone and key press tones. Reminder tones are still active when all tones are disabled.
Press and hold CLOCK for 5 seconds. “ALL SOUNDS ON” or “ALL SOUNDS OFF” will appear in the display. Press and hold CLOCK again to change setting.
To exit, press CANCEL/OFF.
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to Celsius.
To change: Press and hold PRECISE CLEAN for 5 seconds. A tone will sound, and “°C” or “°F” will appear on the display. Repeat to change back.
To exit, press CANCEL/OFF.
7
