16.Remove quarter inch by seven inch pins from top and bottom holes.

17.Set parking brake and start the engine (set throttle at full speed). Make sure that the PTO is off.

18.Rotate rods (lengthen or shorten) to bring each hydrostat to neutral.

NOTE: The control linkage going to the hydrostatic pump has left-hand threads at the pump and right-hand threads at the tower.

19.Tighten the jam nuts earlier loosened.

20.Reassemble safety switches.

21.Reassemble body panels.

22.Reassemble drive handle assembly.

23.Make sure that all hardware is tightened.

SECTION 7: LUBRICATION

Use the two tables that follow for lubrication details. The first table is for oil details and the second table is for grease point information.

Oil

Check

 

Change

 

Capacity

Type

 

 

 

 

 

 

 

 

 

 

 

Engine crankcase

See Engine Operator’s Manual Section

 

 

 

 

 

 

 

 

 

 

 

 

Hydraulic units

50 Hours

 

500 Hours

 

9.5 Quarts

Part Number 737-0305 (10W40 motor oil)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Grease Point

 

 

When to Grease

Type of Grease

 

 

 

 

 

 

 

 

Caster Ass’y - 3 fittings (1 on each

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

wheel spindle and one on middle of

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

caster assembly)

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

Caster wheels - 2 fittings (1 on each

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

wheel)

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Control Tower - 2 fittings

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

(Right side of tower)

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Deck Lift Pivot

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Lift Handle

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Mower Deck

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

 

 

 

 

19

Page 19
Image 19
White Outdoor Z-185L, Z-205, Z-225 manual Lubrication, Oil Check Change Capacity Type