6.SOLUTION STRAINER

The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled

7.BRUSH MOTOR

!

Do not use a pressure washer to clean around the brush motors. Use tap pressure only.

CHANGING BRUSH MOTORS

1.With the scrub deck in the stored position, disconnect brush motor wiring connector from harness.

2.Remove shrouds from scrub deck to access and remove scrub brushes or pad drivers.

3.Remove retaining bolt, lock washer, flat washer and star drive from brush motor shaft.

4.Remove 4 brush motor mounting bolts located under scrub deck.

5.Remove brush motor.

6.Reverse steps to install.

MAINTENANCE

NOTE: Failure to insure all brushes are released will result in motor failure.

8.Reset end cap and realign with scribe marks on motor barrel. Reinstall the two attach bolts from cap into base.

9.Maintain alignment between motor barrel base and cap.

GREASING AXLES

1-2 strokes of Mobiltemp®78 or compatible clay- based or calcium-based grease.

NOTE: Use hand operated grease gun only.

BRUSH MOTOR CARBON BRUSH

REPLACEMENT

1.Scribe alignment mark on motor barrel to motor cap. Remove two bolts.

2.Remove end cap from motor.

NOTE: Motors contain two wave washers in cap. Do not lose these.

3.Release brush from spring tension. Remove screw connecting brush wire lead to brush holder. Clean brush holder to insure free movement.

4.Retract spring and install new brush. Install connector screw and lead.

5.When all new brushes are installed. Place all in retracted position, held into brush holder by spring tension.

6.Carefully place end cap onto bearing on motor shaft.

NOTE: Use care to assure wave washer alignment.

7.With end cap in partially installed position, release all brushes to contact position with motor commutator.

CUTTER 36V 86039090 04/03/07

4-9

Page 26 Page 28
Page 27
Image 27
Windsor SCC326 10052260 Solution Strainer, Changing Brush Motors, Greasing Axles, Brush Motor Carbon Brush Replacement
Page 26 Page 28

SC326 10052220, SCC326 10052260 specifications

The Windsor SCC326 and SC326 series represent innovative advancements in industrial cleaning equipment, designed to enhance efficiency and productivity in various environments. Specifically tailored for heavy-duty cleaning applications, these floor scrubbers combine powerful performance with user-centric features.

The SCC326 model boasts a robust design that is perfect for large commercial spaces like warehouses, airports, and shopping centers. Equipped with a high-capacity solution tank, the SCC326 enables prolonged cleaning sessions without frequent refills, minimizing downtime. The brush system utilizes dual rotating brushes to effectively agitate dirt and grime from surfaces, while the innovative scrub deck design allows for superior maneuverability in tight areas.

On the other hand, the SC326 model shares many of these characteristics but places an added emphasis on eco-friendly operation. With a focus on sustainability, the SC326 incorporates a smart scrub feature that optimizes water and chemical usage, ensuring that cleaning solutions are applied precisely where needed. This not only reduces environmental impact but also lowers operational costs over time.

Both models utilize advanced technology in their respective operations. They come equipped with an onboard diagnostic system, providing real-time feedback on performance and maintenance needs. This feature assists operators in staying informed about the machine's condition and significantly enhances reliability.

Ergonomically designed controls on both models ensure that users can operate them with minimal strain, promoting comfort during extended use. Additionally, their compact design allows for easy storage and transport, making them an excellent choice for businesses with diverse cleaning needs.

In terms of safety, both SCC326 and SC326 are fitted with automatic shut-off systems that activate in case of emergencies, thereby protecting users and equipment alike. This attention to safety standards reflects Windsor's commitment to providing top-tier cleaning solutions.

Ultimately, the Windsor SCC326 and SC326 series embody a blend of power, efficiency, and safety, catering to the rigorous demands of industrial cleaning tasks. Whether addressing large-scale surface areas or caring for intricate spaces, these models are engineered to deliver superior performance without compromising ease of use or environmental responsibility.
Top Page Image Contents