SERVICE

LUBRICATION

Grease blade spindle shaft every 24 hours of operation until some grease is forced out around top of shaft. This is necessary to ensure that enough grease has been forced in to reach top bearing of spindle. V-belt idlers have sealed ball bearings and do not need lubri- cation.

V-BELT

Belt should be adjusted so it is tight enough to hold power of tractor when mowing. When belt replacement is necessary, use only the belt recommended by your Woods dealer. These belts are of special construction for shock loading and severe use. Idler pulleys must be kept in proper alignment so that V-belt will run smoothly.

MAIN SPINDLE ASSEMBLY

The spindle assembly is equipped with two tapered roller bearings. Proper adjustment is maintained by a sleeve welded on the shaft. These bearings are not intended to be adjusted during their useful life.

BLADE SERVICING

Removal

Loosen locking bolt, rotate blade retainer and drive blade pin up out of crossbar and blade. Slide blade out of crossbar. Always sharpen or replace blades in pairs to maintain proper balance. Use genuine Woods blades for replacement. They are made of special steel alloy and are subjected to rigid heat-treat and inspec- tion requirements. Substitute blades may not meet these rigid specifications and could be dangerous.

Installation

LA1

Figure 1. Clockwise Rotation Crossbar

NOTE: On 42-6 mowers, all crossbars rotate in a clock- wise rotation except models L42AC/B & C-6 C L42A-6. Ensure you order correct replacement blades and install them correctly for your machine. Insert blade into crossbar; ensure cutting edge points in direction of crossbar rotation. Install blade pin into crossbar through blade; rotate blade retainer over blade and tighten locking bolt.

LUBRICATION OF OVERRUNNING CLUTCH

Oil only occasionally and just enough to keep a film of oil on internal parts. Excess oil will prevent ratchet teeth from fully engaging, resulting in premature failure.

CLEANING

After Each Use

●Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Inspect machine and replace worn or damaged parts.

●Replace any safety decals that are missing or not readable.

Periodically or Before Extended Storage

●Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Remove the remainder using a low-pressure water spray.

1.Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface.

2.Be careful when spraying near chipped or scratched paint as water spray can lift paint.

3.If a pressure washer is used, follow the advice of the pressure washer manufacturer.

●Inspect machine and replace worn or damaged parts.

●Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer).

●Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing.

8Service

(Rev. 3/14/2008) 29900 (Rev. 7/6/2007)

Page 7 Page 9
Page 8
Image 8
Woods Equipment 42C-6 manual Service
Page 7 Page 9

42C-6 specifications

Woods Equipment has a long-standing reputation for producing high-quality agricultural implements and attachments, and the 42C-6 is a standout in their lineup. Designed primarily for compact utility tractors, this rotary cutter is engineered to offer reliable performance, durability, and ease of use for both commercial and residential applications.

One of the main features of the Woods 42C-6 is its cutting width of 42 inches, making it an ideal choice for maneuvering in tight spaces without sacrificing productivity. It is equipped with a heavy-duty steel deck that provides exceptional strength and durability, allowing it to handle tough brush and grass with ease. The cutter incorporates reinforced sidebands and a robust frame, ensuring a long lifespan even under rigorous conditions.

The 42C-6 showcases advanced cutting technology with its high-speed blade rotation. This feature enhances the efficiency of grass and brush cutting, delivering a clean and precise cut. Additionally, the blades are designed to be easily replaceable, which simplifies maintenance and reduces downtime for operators.

Another notable characteristic is the adjustable hitch. The Woods 42C-6 offers a universal mount that allows compatibility with a wide range of tractor models. This flexibility makes it an attractive choice for farm owners and landscaping businesses seeking to maximize their equipment's versatility.

Safety is a priority in the design of the 42C-6. It is equipped with a safety guard that minimizes the risk of debris being flung from the cutter, ensuring a safer working environment. The cutter also features a slip clutch that protects the driveline from overload, further enhancing its reliability during operation.

Ease of operation is another significant advantage of the Woods 42C-6. With a straightforward attachment process, operators can quickly connect and disconnect the cutter, saving valuable time during job transitions. The cutter's lightweight design further enhances maneuverability, allowing users to navigate around obstacles with confidence.

In summary, the Woods Equipment 42C-6 rotary cutter combines durability, efficiency, and safety in a compact package designed for various cutting needs. With its robust construction, ease of use, and reliable performance, it is well-suited for those looking to tackle tough mowing jobs in a variety of settings. Whether for agricultural use or landscaping projects, the 42C-6 stands as a testament to Woods Equipment's commitment to quality and innovation in outdoor equipment.
Top Page Image Contents