C H E C K L I S T S

DELIVERY CHECKLIST

 

DAILY CHECKLIST

Inspect the cutter thoroughly after assembly to be certain it is set up properly. The following checklist is a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

hCheck operator's manual and familiarize the opera- tor with all sections of it.

hCheck that all safety shielding is in place.

hCheck all bolts to be sure they are tight or adjusted properly at hinged locations.

hCheck that all cotter pins are properly installed.

hCheck PTO driveline. Make sure it is the correct length to operate cutter with intended tractor.

hCheck that all lubrication points with grease fittings have been lubricated.

hCheck that blades have been properly installed. Check all blade beam bolts.

hCheck cutter attitude, after mounting on tractor.

hCheck that gearbox is properly serviced and seals are not leaking.

hCheck shear bolt for proper grade and installation.

hCheck front of input gearbox shaft and make sure that snap ring is properly installed.

hAll safety signs (decals) in place and readable.

hWhen the cutter is transported on a road or highway at night or during the day, safety devices should be used for adequate warning to operators of other vehicles.

hCheck that cutter is properly and securely attached to tractor.

hDuring inspection, check that all nuts and bolts are secure and that all safety shields are in place.

hIt is very important that the blade carrier nut and blade bolts are checked and tightened frequently.

hCheck condition of blades and security of attach- ment.

hCheck that PTO driveline shields are securely locked and clears the front of the cutter frame.

hAdjust the tractor top link so the front of the cutter is slightly above the rear. Then raise the tractor lift very slowly, making sure that the front drive shaft shield does not hit the front of the cutter. If it does, damage will be done to the drive shaft shield and, if it hits hard enough, it will also damage the drive shaft itself. (See page 20.)

NOTE: This type of damage is not covered under warranty, as it is totally under the control and the responsibility of the operator.

I M P O RTANT!

Gearbox was not filled at factory. It must be serviced before operating. Fill to proper level with SAE 90 oil. Failure to service will result in damage to gearbox.

3

Page 3 Page 5
Page 4
Image 4
Worksaver SDM40-72, SDM40-48, SDM40-60 manual E C K L I S T S, Delivery Checklist Daily Checklist
Page 3 Page 5

SDM40-60, SDM40-48, SDM40-72 specifications

The Worksaver SDM series, including models SDM40-72, SDM40-48, and SDM40-60, represents a significant advancement in material handling technology designed for agricultural and landscaping applications. These robust and versatile skid-steer and tractor attachments provide users with an efficient solution for a variety of tasks, including moving and grading soil, gravel, and other materials.

The SDM40-72 model boasts a 72-inch wide blade, while the SDM40-48 and SDM40-60 come with 48-inch and 60-inch blades, respectively. This range in size allows users to choose the perfect model to fit their specific needs and the dimensions of their equipment. The heavy-duty construction of the blades ensures durability and toughness, capable of withstanding rigorous use in demanding environments.

One of the standout features of the Worksaver SDM series is the intelligent design of the blade itself. The blades are equipped with a quick-attach system, making it easy for operators to switch attachments quickly, enhancing productivity on the job site. This feature is particularly valuable for contractors who may need to adapt to varying application requirements throughout the day.

The SDM series also incorporates innovative tilt and angle adjustment mechanisms. This allows operators to fine-tune the blade position for precise material handling and grading. With adjustable tilt angles, users can achieve optimal results whether they are leveling surfaces, backfilling, or creating drainage ditches.

Additionally, the Worksaver SDM models are designed to integrate seamlessly with a variety of skid-steers and tractors, ensuring versatility across different machinery brands. The universal mounting plate allows for quick attachment to most popular equipment models, eliminating compatibility issues that can slow down operations.

Safety is prioritized in the design of the SDM series, which includes reinforced edges and a robust framework. This ensures not only the safety of the operator but also the longevity of the attachment. The blades are constructed from high-quality materials designed to resist wear and enhance performance over time.

In summary, the Worksaver SDM40-72, SDM40-48, and SDM40-60 models are exceptional choices for professionals seeking reliable and efficient material handling solutions. Their innovative features, durable construction, and compatibility with various equipment make them ideal for tackling a wide range of tasks in agricultural and landscaping applications. Users can expect enhanced efficiency and productivity with these outstanding attachments.
Top Page Image Contents