Xantech CC12 RC68+ PROGRAMMER / REMOTE CONTROL, APPLICABLE RC68+ BUTTON DESCRIPTIONS

RC68+ PROGRAMMER / REMOTE CONTROL

The RC68+ Programmer (available separately) contains all the commands necessary to operate the CC12.

•You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link, etc., with commands that operate the CC12.

•NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, RP41AV, ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the CC12 (OVERLAY 'B') are listed below. All others should be ignored.

CAUTION: While the RC68+ will operate as a separate remote control, it is highly recommended it not be given to the final user for the following reasons:

•Since it includes setable code groups, the user may inadvertently alter the installer configurations.

•Also, since the user will require IR commands from other brands of equipment to control the total system, in addition to those of the CC12, all commands should be consolidated into one learning device, for ease of use.

APPLICABLE RC68+ BUTTON DESCRIPTIONS

	1.	Pair OFF Command. This button activates the IR command that
		turns the internal relay of the CC12 to the OFF position (the N/C
		selection).
.	2.	Pair ON Command. This button activates the IR command that
		turns the internal relay of the CC12 to the ON position (the N/O
		selection).
	3.	TGL (toggle) Command. The first press of this button turns the
		relay ON (the N/O selection) - the second press turns it OFF (the
		N/C selection).
	4.	MMT (momentary) Command. Pressing this button causes the
		CC12 relay to go ON (the N/O selection) but stays ON only as long
		as the button is held down. When released, the relay returns to the
		OFF position (the N/C selection).
	5.	IR Emitter Lens.

CODE SUB-GROUP

	5							1
CODE											2
SUB-								3
GROUP
								4
0								B
		0	80	48	10	90	01
			OFF	ON	TGL	MMT
1									Place the
		1	00	C0	50	D0	41
			OFF	ON	TGL	MMT			"B" Overlay
2
		2	40	A0	30	B0	21		on the RC68+
			OFF	ON	TGL	MMT
3
		3	20	E0	70	F0	61
			OFF	ON	TGL	MMT
4
		4	60	88	18	98	09		RC68+
			OFF	ON	TGL	MMT
5
		5	08	A8	38	B8	29
			OFF	ON	TGL	MMT
6
		6	28	E8	78	F8	69
			OFF	ON	TGL	MMT
7										6
		7	68	C8	58	D8	49
			OFF	ON	TGL	MMT
			E1	89	C9	A9	E9
			71	19	59	39	79
			F1	99	D9	B9	F9

The RC68+ has 11 rows of 5 buttons each. Each row, identified by the	Fig. 2 The RC68 Programmer
numbers 0 through 7 (see Fig. 2), will execute the same set of 4

commands listed above, when selected by the CODE SUB-GROUPswitch on the CC12. This is useful to prevent mutual interaction in common IR systems when using more than one CC12, or if SR21's are used with CC12's.

To change the CODE SUB-GROUP, simply rotate the CODE SUB-GROUP switch on the CC12 to the number that corresponds to the desired row on the RC68+. Remove and reapply power (after 20 seconds), then use the chosen row to execute the commands for that particular CC12.

NOTE: No changes are needed on the RC68+!

6.Code Group Numbers. The CC12 is also capable of being set to different basic code groups as well as the sub-groups.

NOTE: When shipped from the factory, the CC12 is set to code group number 50. Be sure to set the RC68+ to the same number!

It may be necessary to change the CC12 to a different code group if it is used in a common IR bus controlled system with many CC12'S, SR21's, etc., to avoid mutual interaction.

Refer to the RC68+ instructions for code group setting procedures.

2 

CC12