FCC REQUIREMENTS

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as determined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this DPC100 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If the DPC100 causes harm to the telephone network, the telephone company will notify you in advance that –temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service. If trouble is experienced with the DPC100 for repair or warranty information, please contact:

XANTECH CORPORATION, 13100 TELFAIR AVE. SYLMAR, CA 91342 (818) 362-0353

If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS: Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours, such as early morning or late evenings. It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.

PART 15 LIMITATIONS

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Xantech Corporation 13100 Telfair Avenue, 2/F Sylmar, CA 91342

Installation Instructions, DPC100

© 2007 Xantech Corporation, Document #08905106B

This document is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Xantech

Corporation.

Xantech Corporation shall not be liable for operational, technical, or editorial errors/omissions made in this document.

 

 

08905106B

- 6 -

Page 5 Page 6
Page 6
Image 6
Xantech DPC100 installation instructions Xantech CORPORATION, 13100 Telfair AVE. SYLMAR, CA 91342 818
Page 5 Page 6

DPC100 specifications

The Xantech DPC100 is a sophisticated digital programmable controller designed to enhance automated control systems in residential and commercial settings. Renowned for its versatility and user-friendly interface, the DPC100 is a valuable asset for integrators and end-users alike.

One of the main features of the DPC100 is its advanced programmability. Equipped with a powerful microcontroller, this device allows users to create custom control sequences tailored to specific needs. With its easy-to-navigate programming interface, users can easily set up complex automation scenarios, making it an excellent option for managing multiple devices simultaneously.

Moreover, the DPC100 supports a variety of communication protocols, including IR, RS-232, and RF, ensuring compatibility with a wide range of home automation devices. This multi-protocol support allows users to integrate various systems, such as lighting, HVAC, and audiovisual equipment, into a single cohesive network. The DPC100 comes with a dedicated IR output, ensuring seamless integration with Xantech’s extensive line of IR control products.

Another notable characteristic of the DPC100 is its robust performance in multitasking environments. With the ability to manage several devices at once, it enhances system efficiency and streamlines user experience. This capability is particularly beneficial in environments where multiple devices need to be controlled concurrently, reducing the need for multiple remotes and simplifying operation.

The device also boasts a reliable power management system. Featuring a low power consumption design, the DPC100 minimizes energy use without sacrificing performance. This aspect not only contributes to cost savings in energy bills but also aligns with modern sustainability goals.

In terms of user experience, the DPC100 shines with its intuitive setup process. The inclusion of a comprehensive user manual, coupled with tutorials and support resources, assists users in configuring the device with ease. Whether for residential home theaters or commercial audio-visual setups, the learning curve is minimal, allowing quick implementation.

In conclusion, the Xantech DPC100 is a powerful and adaptable digital programmable controller that enhances automation in various environments. With features such as advanced programmability, multi-protocol support, robust multitasking capabilities, and energy-efficient design, it stands out as a leading choice for users seeking a reliable automation solution. The DPC100’s excellent performance and ease of use make it a trusted component in the landscape of modern control systems.
Top Page Image Contents