|
|
| 8 | 9 | A |
|
|
|
| 8 | 9 | A |
|
|
|
|
| 8 | 9 | A |
|
|
|
| 8 | 9 | A |
|
| ||||
|
|
| 7 |
|
|
|
|
|
| 7 |
|
|
|
|
|
|
| 7 |
|
|
|
|
|
| 7 |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| B |
|
|
|
| B | ||||||||||
| 5 | 6 |
|
| B | 5 | 6 |
|
| B |
| 5 | 6 |
|
|
| 5 | 6 |
|
|
| ||||||||||||
RC68+ |
|
|
|
| C |
|
|
|
| C | RC68+ |
|
|
|
| C |
|
|
|
| C | ||||||||||||
4 |
|
|
|
|
| D | 4 |
|
|
|
|
| D | 4 |
|
|
|
|
| D | 4 |
|
|
|
|
| D | ||||||
(rear | 3 |
|
|
| E | 3 |
|
|
| E | (rear | 3 |
|
|
| E | 3 |
|
|
| E | ||||||||||||
|
| 2 |
|
| F |
|
|
| 2 |
|
| F |
|
|
| 2 |
|
| F |
|
|
| 2 |
|
| F |
| ||||||
panel) |
|
| 1 | 0 |
|
|
|
| 1 | 0 |
|
| panel) |
|
| 1 | 0 |
|
|
|
| 1 | 0 |
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| CODE GROUP |
|
| CODE GROUP |
| ||||||||||||||||||||||||||
|
|
| 8 | 9 | AB |
|
| 8 | 9 | AB |
|
|
|
| 8 | 9 | A |
|
|
|
| 8 | 9 | A |
|
|
| ||||
|
|
|
|
|
|
|
|
| 7 |
|
|
|
|
| 7 |
|
|
|
| ||||||||||||
|
| 6 | 7 |
|
| 6 | 7 |
|
|
| 5 | 6 |
|
| B | 5 | 6 |
|
| B |
| ||||||||||
| 5 |
|
|
| C | 5 |
|
|
| C |
|
|
|
|
| C |
|
|
| C |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
| 4 |
|
|
| E | D | 4 |
|
|
| E | D |
|
| 3 |
|
| E | D | 3 |
|
| E | D |
| ||||||
| 3 |
|
| 3 |
|
|
|
|
|
| 2 |
| F |
|
|
| 2 |
| F |
| 2nd Digit | ||||||||||
|
|
| 2 |
| F |
|
|
| 2 |
| F |
|
|
|
|
| 0 |
|
|
|
| 0 |
|
| |||||||
1st Digit |
|
| 1 | 0 |
|
|
|
|
| 1 | 0 |
|
|
| 2nd Digit | 1st Digit |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
(Left) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (Right) | (Left) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (Right) |
FIG. 5 Switches set to FF for Code Group changes. | FIG. 6 Setting the code switches to the newly changed | |
code. Refer to step 6. (30 shown for MIRV1/RAT1). | ||
Refer to step 2. | ||
|
2.Using a small blade screwdriver, rotate each of the two Code Group Setting Switches on the rear of the RC68+ to the F position (FF). See Fig. 5.
3.Turn the remote over and locate a Code Group number that is different than any other Xantech model used in the same system (i.e., 48, D0, C0, etc.). These numbers are printed on the front face of each RC68+ button! (See item #17, Fig. 3).
4.Aim the RC68+ at the Xantech IR receiver (780, 480, etc.) and press the button that has the number on it that you decided on.
5.The control chip in the Xantech device (MIRV1/RAT1, RS41AV, etc.) will now change to respond to the code you selected.
6.Test the system by rotating each of the Code Group Setting Switches on the rear of the RC68+ to the chosen code number (refer to Fig. 6). The Left switch is the first digit in the number and the Right one is the second digit.
The device should now respond to the RC68+ commands that relate to the operational functions of that device (i.e., volume up/down, input selection, etc.).
7.Repeat this procedure, as necessary, for each duplicated Xantech device you have in the same system (except the ZPR68), changing the Code Group each time.
8.When you have completed the Code Group settings for each device, you may then connect them into the same IR network. You will now need to "teach" these commands into learning devices such as the Xantech URC series Learning Remotes, SmartPads, etc.
Be sure to change the Code Group Setting Switches on the rear of the RC68+ (Fig. 6) to match the newly changed code number you set for each device, during the teaching process.
|
|
| 5 |
|
RC68+ | |
|
| |
|
|
|
|
|
|
|
|
|
|
