GB

Xpelair Toilet/Bathroom Fans DX100, DX100PC, DX100T, DX100H, DX100HP DX100PIR & DX100VTD installation & operating instructions

Please leave this leaflet with the fan for the benefit of the user

3.If the shaft has cavity wall, use the wall tube to bridge the cavity.

4.Fit ducting and condensation trap if necessary, positioning condensation trap as near to the fan as possible.

If installing in a ceiling

1.Check there are no buried pipes or cables in the ceiling/joists etc.

If in doubt, seek professional advise.

2.Cut a hole 115mm diameter.

Preparing the fan for installation

Remove the front cover by pressing the release catches located on the sides of the unit with a 3mm screwdriver, whilst pulling the front cover

forward L

Mount the fan in the hole

If working above ground floor level, appropriate safety precautions must be observed.

If installing in a wall, ceiling or vent

Mark the position of the back plate B

1.Hold the backplate so that the terminal block faces you in the top left hand corner and the lip points towards the hole.

2.Carefully insert the lip into the wall duct/ceiling or vent shaft.

3.Adjust the position of the back plate until it is level.

4.Mark on the wall/ceiling or vent shaft the positions of the three fixing holes in the back plate.

5.Remove the back plate from the ducting.

6.Drill screw holes in these positions if necessary, and fit wall plugs if necessary.

Mount the back plate C

1.Push the ribbed gasket (RG100) onto the lip of the back plate 1

2.If installing in a ceiling or vent, push the larger diameter piece of the telescopic wall tube onto the ribbed gasket. Cut the tube to the required length first, if necessary.

3.If wiring the fan from behind, remove knockout. Feed the mains cable through the cable entry hole in the back plate to the terminals D.

4.If wiring from above, leave the cable free to be fitted into labyrinth.

5.Insert the lip of the back plate into the wall duct/ceiling or vent shaft as before.

6.Fasten the back plate to the wall/ceiling or vent shaft using appropriate fasteners. If using screws, do not overtighten the screws.

Mount the back draught shutter

1.Peel the backing from the foam strip supplied and attach it around the outside of the lip on the back draught shutter.

2.Go outside. Holding open the top and bottom vanes, insert the lip into the wall duct.

3.Making sure that the back draught shutter is level, mark the positions of the two fixing holes in the top right hand and bottom left hand corners.

4.Remove the back draught from the wall duct.

5.Drill screw holes in these positions, and fit the remaining wall plugs.

6.Holding open the top and bottom vanes, refit the back draught shutter and fasten it to the wall using the pointed and self-tapping screws. Do not over tighten screws.

7.Make sure that the vanes open and shut freely.

If installing in window or panel

Sealing the hole E

1.If installing in a window or panel no more than 9mm thick, fit the white rubber gasket around the edge of the hole. If installing in a panel or sealed double glazing more than 9mm thick, a DXDG double glazing kit is required. Follow the instructions supplied with the special kit.

Attach the back draught shutter to the spacer F

1.Holding the top and bottom vanes, insert the back draught shutter 2 into the spacer 3 so that the fixing holes in the top right and bottom left hand corners match those on the spacer.

2.Insert two of the flat ended self-tapping screws provided and fasten the back draught shutter to the spacer.

Mount the fan in the window G

1.Someone else must hold the back draught shutter and spacer in position outside, with the spacer against the glass.

2.Make sure that the two raised fixing holes in the spacer are horizontal and are positioned within the hole.

3.From inside, hold the back plate so that the terminal block faces you in the top left hand corner and the lip points towards that hole.

4.Align the holes in the back plate with those in the spacer.

5.Insert two of the flat ended self-tapping screws provided in the fixing holes, and fasten the back plate to the spacer. Do not overtighten the screws.

Wire the electrical connections

•Make sure the mains supply is isolated,

1.Wire the fan as shown in H check the fan model to diagram, feeding the cable between the two raised pegs, if wiring from above, and through labyrinth to terminal block.

2.Switch off the mains electrical supply and remove fuses

3.Connect the cable from the isolating switch to the electrical supply wiring.

•For fixed wiring circuits the protective

6

Page 5 Page 7
Page 6
Image 6
Xpelair DX100HP, DX100T Preparing the fan for installation, Mount the fan in the hole, Wire the electrical connections
Page 5 Page 7

DX100H, DX100PC, DX100VTD, DX100PIR, DX100 specifications

The Xpelair DX100 range offers a selection of high-performance ventilation solutions designed to enhance air quality and comfort in residential and commercial environments. Among the key models are the DX100PIR, DX100VTD, DX100PC, DX100H, and DX100T, each catering to specific needs while sharing core features that reflect Xpelair's commitment to innovation and efficiency.

The DX100PIR is equipped with a passive infrared sensor, allowing it to detect occupancy and adjust its operation accordingly. This intelligent feature ensures energy conservation by only activating when someone is present in the room, making it ideal for bathrooms, hallways, and other frequently used spaces. Its stylish design and low-profile structure blend seamlessly with modern interiors.

The DX100VTD model boasts an advanced timer and delay function, permitting users to set how long the fan runs after being activated. This is particularly useful in areas prone to excess humidity, such as kitchens and bathrooms, where moisture management is essential for preventing mold growth and maintaining a healthy environment.

With the DX100PC, users benefit from an easy-to-install unit specifically designed to address humidity control. This model features a unique pull cord operation that allows users to override the automatic functionalities, providing an added layer of versatility for varying usage scenarios.

The DX100H is tailored for heating and ventilation, integrating a heater to maintain a comfortable temperature while ensuring fresh air circulation. This model is perfect for colder climates where warmth and ventilation must be balanced efficiently.

Lastly, the DX100T is a timer-controlled unit suited for spaces requiring extended ventilation without continuous energy consumption. It features an adjustable timer, providing flexibility and control over the duration of airflow, crucial for spaces affected by moisture or odors.

All models within the Xpelair DX100 series feature quiet operation, making them suitable for residential areas without causing disturbances. Additionally, they are designed with energy efficiency in mind, helping to reduce electric consumption while promoting sustainable living. Constructed with high-quality materials, these units promise durability and reliability, further solidifying Xpelair’s reputation as a leader in ventilation solutions. Whether for bathrooms, kitchens, or homes requiring enhanced air quality, the DX100 series provides tailored solutions that ensure comfort and cleanliness while minimizing energy usage.
Top Page Image Contents