Part Names and Functions

■Remote control

Buttons with identical names to those on the main unit perform identical functions. To use the remote, point it at the remote control sensor on the front or back of the unit from a distance of no more than 7 m (23 feet).

1

 

 

 

 

2

 

 

 

e

3

AUTO

 

 

r

 

V. POS

ZOOM

FOCUS

 

4

IRIS

SETTING PATT

 

 

 

5

 

 

 

t

6

ESCAPE

 

MENU

y

7

 

 

 

 

 

 

 

 

u

8

ASPECT

 

INPUT

i

 

LIGHT

 

 

o

9

STILL

INPUT

HIDE

p

 

 

 

 

0

S VIDEO

A

DVI

 

 

VIDEO

B

D4

 

 

 

MEMORY

 

 

q

1

2

3

 

 

 

 

 

 

4

5

6

 

w

RESET

1Transmit indicator

This indicator will light up when the unit is sending infra-red signals to the main unit.

2AUTO button

Pressing this button will automatically adjust the unit to the best settings for projection by retuning the frequency of the projection to that of the source component.

3V. POS button

Switches on and off the adjustment mode for the vertical positioning of the entire image.

0INPUT area

Directly selects the input jack.

qMEMORY area

Calls up stored video memory directly.

wRESET button

Press this button to reset all parameters altered in the menu to their default factory settings.

e button

Switches the unit between Standby and On (operational) modes.

rFOCUS button

Switches on and off the focus adjustment mode for the image being projected.

tPATT (PATTERN) button

Switches the built-in test pattern display on and off.

yMENU button

Press this button to display the general settings and adjustments menu.

u (Enter) button

Use this button to set values and enter into submenus when the menu is being displayed. Pressing the button when the menu is not being displayed will call up the in-line menu. (see page 28.)

iINPUT button

Press this button to display the input source and input signal selection menu.

oLIGHT switch

Pressing this switch will light up the often used 2, 6, 8, e, y, i buttons. The lights will switch off if no operation is performed within 10 seconds.

pHIDE button

Press this button to temporarily halt projection of the image being displayed. Press the HIDE button once more to cancel this function.

4ZOOM button

Switches on and off the size adjustment mode for the image being projected.

5IRIS button

Switches on and off the lens iris diaphragm change mode.

6ESCAPE button

Press this button to exit from a sub-menu.

7 Cursor buttons

Use the h, g, –, + buttons to move the cursor within the

interface.

 

 

 

 

ESCAPE

 

 

 

 

ASPECT

 

 

S

ST

INPUT

 

 

ILL

 

 

VIDEO

 

 

 

 

VI

 

H

 

 

DE

A

 

 

O

IDE

 

1

B

 

DVI

 

 

 

4

 

2

 

D4

 

 

 

 

 

5

 

3

 

RESET

 

6

 

 

s

 

AUTO

 

 

 

 

V.

 

 

 

 

POS

 

 

 

IRIS

ZOOM

 

 

 

 

 

FOCUS

 

 

 

PATT

 

 

 

MEN

 

 

-1

 

U

 

ID

 

 

 

 

 

 

ID

-2

 

 

 

 

 

a

8ASPECT button

Selects the display aspect of the projection image. Press the button to display the aspect presently being used. Pressing the button again within 2 seconds will switch the unit to the next aspect mode.

9STILL button

Stops a moving image to display a still of the desired image. Press STILL again to cancel this function.

aRemote control code switching switch

This remote control will work when it has the same code as that set on the menu. The default setting on the menu is ID-1.

sRemote control cable jack

Use this jack to connect the remote control to the main unit with a cable.

E-4