OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL

Setting the manufacturer code (remote control signal assigned to each manufacturer) for your TV, VCR or MD/ CD recorder on the remote control allows you to operate not only the DVX-S100 but also your TV, VCR or MD/ CD recorder using the remote control.

Note

•Depending on the model, certain components from other manufacturers cannot be controlled, or only limited functions can be controlled, even though the proper manufacturer code has been set. If you encounter this problem, please use the remote control supplied with the component.

2Keeping CODE SET pressed, enter the 1- digit device code and the 2-digit manufacturer code for the component to be controlled using the numeric buttons.

You can release CODE SET after entering the code.

y

•The manufacturer code 99 has been set for the remote control selector buttons (TV, VCR and MD/CD-R) at the factory.

3Press POWER (TV or AV) and check that the component to be controlled turns on and off (standby).

Setting the manufacturer code

Manufacturer codes can be set for TV, VCR and MD/ CD-R buttons only.

Note

•TV manufacturer codes can be set for the TV button only. However, any of the manufacturer codes can be set for the VCR and MD/CD-R buttons.

 

POWER

 

 

POWER

AV

TV

TV

AV

 

SLEEP

 

 

 

TV MODE

 

 

 

 

INPUT

 

 

TUNER

 

 

CH

 

 

VOL

MD

MD/CD-R

 

 

 

 

 

 

 

MUTE

 

 

CD–R

 

SUBTITLE

 

 

AUDIO

 

VCR

 

REC

 

 

 

VCR

 

 

 

 

 

VIDEO 2

 

 

 

 

 

 

VIDEO 1

 

CODE SET

CODE SET

 

 

CD

 

 

SHIFT

 

 

DVD

AMP

 

 

HALL

JAZZ

 

ROCK

ENTERTAINMENT

 

 

1

2

 

3

4

Numeric buttons

 

 

SETUP

 

ANGLE

MARKER

 

SPORTS MONO MOVIE

MOVIE 1

MOVIE 2

 

 

5

6

 

7

8

 

 

 

PLAY MODE

REPEAT

A–B

 

 

/DTS

SELECT

 

MATRIX 6.1

STEREO

 

 

9

0

 

>–10

CANCEL

 

 

 

 

 

GROUP

PAGE

 

 

TOP MENU

MENU

 

 

 

LEVEL

SET MENU

MUTE

 

 

 

 

 

 

 

 

 

PRESET

 

ABCDE

 

 

 

CH

ENTER

 

CH

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

TEST

B. BOOST

VOL

 

 

ON SCREEN

RETURN

 

(U.S.A. model)

1While pressing CODE SET, press the input selector button (TV, VCR, MD/CD-R) for which the manufacturer code is to be set.

Only one manufacturer code can be set for each input selector button.

Note

•Keep pressing CODE SET between step 1 and 2.

Precautions when performing the setting

You can operate the component using the TV, VCR or MD/CD-R operation buttons on the remote control once the manufacturer code is set properly. If unsuccessful, perform the procedure from step 1 again. Pay attention to the following points when you perform the procedure.

•Check that the correct remote control selector button has been selected when setting the manufacturer code.

•If more than one code is given for a manufacturer, try entering each code in the order given.

•Remove and replace the remote control’s batteries (complete this step within 2 minutes) and then perform the procedure. While replacing the batteries, be sure not to press any button on the remote control. Doing so may erase the manufacturer code which has been set for other remote control selector buttons.

To reset the manufacturer code to the factory-set code

Follow steps 1 to 2 for the procedure “Setting the manufacturer code”, and enter the device code for the component and “99” while pressing CODE SET in step 2. (It is not necessary to follow step 3.)

CONTROL REMOTE FEATURES

• Refer to “LIST OF MANUFACTURER’S

CODES” at the end of this manual. English

57