Yamaha HTR-5930 65

TROUBLESHOOTING

	Problem	Cause	Remedy	See
	Problem	Cause	Remedy	page
				page
	The sound suddenly	The protection circuitry has been activated	Check that the impedance selector setting is correct.	9, 11
	goes off.	because of a short circuit, etc.
	goes off.	because of a short circuit, etc.	Check that the speaker wires are not touching each	—
			Check that the speaker wires are not touching each	—
			other and then turn this unit back on.

		The sleep timer has turned off this unit.	Turn on this unit, and play the source again.	—

		The sound is muted.	Press MUTE or VOLUME +/– on the remote control	25
			to resume audio output.

	Sound is heard from	Incorrect cable connections.	Connect the cables properly. If the problem persists,	13-17
	the speaker on one		the cables may be defective.
	side only.
	side only.	Incorrect settings in “SP LEVEL”.	Adjust the “SP LEVEL” settings.	26
		Incorrect settings in “SP LEVEL”.	Adjust the “SP LEVEL” settings.	26

	Only the center	When playing a monaural source with a
	speaker outputs	CINEMA DSP program, the source signal
	substantial sound.	is directed to the center channel, and the
		front and surround speakers output effect
		sounds.

	No sound is heard	“CENTER” in “SET MENU” is set to	Set “CENTER” to “SML” or “LRG”.	53
	from the center	“NONE”.
	speaker.
	speaker.	One of the HiFi DSP programs (except for	Try another sound field program.	30
		One of the HiFi DSP programs (except for	Try another sound field program.	30
		5ch Stereo) has been selected.

	No sound is heard	“SURR” in “SPEAKER SET” is set to	Set “SURR” to “SML” or “LRG”.	54
	from the surround	“NONE”.
	speakers.
	speakers.	This unit is in the “STRAIGHT” mode	Press STRAIGHT on the front panel so that	33
		This unit is in the “STRAIGHT” mode	Press STRAIGHT on the front panel so that	33
		and a monaural source is being played	“STRAIGHT” disappears from the front panel
		back.	display.

	No sound is heard	“BASS” in “SPEAKER SET” is set to	Set “BASS” to “SWFR” or “BOTH”.	54
	from the subwoofer.	“FRNT” when a Dolby Digital or DTS
		signal is being played.

		“BASS” in “SPEAKER SET” is set to	Set “BASS” to “BOTH”.	54
		“SWFR” or “FRNT” when a 2-channel
		source is being played.

The source does not contain low- frequency bass signals.

INFORMATION

ADDITIONAL

61

Contents

Page IMPORTANT SAFETY INSTRUCTIONS FCC INFORMATION (for US customers) CAUTION: READ THIS BEFORE OPERATING YOUR UNIT We Want You Listening For A Lifetime CONTENTS FEATURES Built-in 5-channelpower amplifier Decoders and DSP circuits Sophisticated AM/FM tuner XM Satellite Radio (U.S.A. model only) GETTING STARTED Supplied accessories Installing batteries in the remote control CONTROLS AND FUNCTIONS Front panel APHONES jack BSPEAKERS CSTRAIGHT DTONE CONTROL EBASS/TREBLE +/– Remote control ■Controlling this unit ■Controlling the TUNER functions ■Using the remote control Front panel display Rear panel CONNECTIONS Placing speakers ■Front speakers (FL and FR) ■Center speaker (C) ■Surround speakers (SL and SR) Connecting speakers (U.S.A. and Canada models only) ■Before connecting to the SPEAKERS terminal ■Connecting to the FRONT A SPEAKERS terminals ■FRONT terminals CENTER terminals SURROUND terminals SUBWOOFER OUTPUT jack ■Audio jacks ■Video jacks ■ Connecting a DVD recorder/VCR ■ Connecting a video monitor ■ Connecting a DVD player/cable TV satellite tuner ■ Connecting another video component Page ■Connecting to the COMPONENT VIDEO jacks ■Connecting to the MULTI CH INPUT jacks Connecting audio components ■Connecting a CD player ■Connecting a CD recorder/MD recorder ■Connecting the AM loop antenna Connecting the power cable IMPEDANCE SELECTOR VOLTAGE SELECTOR (Asia and General models only) Turning on the power SETUP Using BASIC MENU Choice Display Speakers 5spk 7Press d to confirm your selection 8Press j/ i to select the desired setting Page PLAYBACK Basic operations Press PROGRAM Additional operations ■Listening with headphones using ■Muting the audio output ■Selecting the MULTI CH INPUT component as the input source ■Selecting the input modes ■Adjusting speaker levels during playback ■Using the test tone ■Displaying information about the input source ■Using the sleep timer ■Playing video sources in the background SOUND FIELD PROGRAMS ■ Front panel operations ■ Remote control operations Sound field program descriptions ■Enjoying 2-channelsources using the standard decoders ■Editing sound fields parameters ■Using Virtual CINEMA DSP ■Listening to unprocessed input signals RECORDING FM/AM TUNING Automatic tuning Manual tuning Automatic preset tuning Manual preset tuning Selecting preset stations Exchanging preset stations XM® SATELLITE RADIO TUNING What is XM Satellite Radio ■Information from XM Satellite Radio Inc XM Satellite Radio controls and functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations Selecting the XM Satellite Radio search mode ■All Channel Search mode ■ Category Search mode ■Preset Search mode ■ Direct Number Access mode Setting XM Satellite Radio preset channels Displaying the XM Satellite Radio information ■Displaying the XM Satellite Radio information in the front panel display When the channel number/name is displayed: When the channel category is displayed: When the artist name/song title is displayed: SET MENU ■BASIC MENU ■SOUND MENU ■INPUT MENU ■OPTION MENU Using SET MENU SOUND MENU ■Speaker settings 1 SPEAKER SET ■Speaker distance 2 SP DISTANCE ■Low-frequencyeffect level 3 LFE LEVEL ■Dynamic range 4 D.RANGE ■Tone bypass 5 TC.BYPASS INPUT MENU ■Input assignment 1 INPUT ASSIGN Input mode OPTION MENU ■Display settings 1 DISPLAY SET ■Memory guard 2 MEM. GUARD Audio mute ■XM Radio setting 4 XM RADIO SET REMOTE CONTROL FEATURES Controlling this unit, a TV, or other components ■ Controlling this unit Controlling a TV ■Controlling other components Setting remote control codes TROUBLESHOOTING ■General Page Page ■Tuner ■XM Satellite Radio (U.S.A. model only) ■Remote control RESETTING THE SYSTEM GLOSSARY Audio information ■Dolby Digital ■Dolby Pro Logic ■Dolby Surround Video information ■Component video signal ■Composite video signal SPECIFICATIONS LIST OF REMOTE CONTROL CODES APPENDIX