8. SYSTEM EXCLUSIVE MESSAGES (XG Standard) 10. SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format:
(1) XG Native Parameter Change
Data format: F0H = Exclusive status
43H = Yamaha ID
F0H = Exclusive status 73H = Digital Piano ID
43H = YAMAHA ID 7FH = Extended Product ID
1nH = When received, n=0–F. 4BH =Product ID
When transmitted, n=0. 11H =Special control
4CH =Model ID of XG 0nH = Control MIDI change (n=channel number)
hhH = Address High ccH = Control number
mmH = Address Mid vvH = Value
llH = Address Low F7H = End of Exclusive
ddH = Data
|Control Channel ccH vvH
F7H = End of Exclusive Channel Detune ch: 00H–0FH 43H(Sets the Detune value
for each channel)
00H–7FH
Voice Reserve ch: 00H–0FH 45H 00H : Reserve off
7FH: on*
*
(2) XG Native Bulk Data (reception only) 11. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: Data format:
F0H = Exclusive status
43H = YAMAHA ID
0nH = When received, n=0–F.
When transmitted, n=0. F0H =Exclusive Status
4CH =Model ID of XG 43H = Yamaha ID
aaH = ByteCount 1nH = When received, n=0–F.
bbH = ByteCount When transmitted, n=0.
hhH = Address High 27H = Model ID of TG100
mmH = Address Mid 30H =Sub ID
llH = Address Low 00H =
ddH = Data 00H =
| | mmH = Master Tune MSB
| | llH = Master Tune LSB
ccH = Check sum ccH =irrelevant (under 7FH)
F7H = End of Exclusive F7H =End of Exclusive
•
•
•
9. SYSTEM EXCLUSIVE MESSAGES
(Digital Piano MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [xxH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Digital Piano ID
01H = Product ID (digital piano common)
xxH = Substatus
nn Control
02H Internal MIDI clock
03H External MIDI clock
06H Bulk Data (the bulk data follows 06H)
F7H = End of Exclusive
For information about the Address and Byte Count values,
refer to Table 1 below. Note that the table’s Total Size value
gives the size of a bulk block. Only the top address of the
block (00H, 00H, 00H) is valid as a bulk data address.
When Volume, Expression is received for Reserve On,
they will be effective from the next Key On. Reserve Off is
normal.
Master Tuning (XG and last message priority)
simultaneously changes the pitch of all channels.
[F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->
[mmH] -> [llH] -> [ddH] -> [F7H]
Receipt of the XG SYSTEM ON message causes
reinitialization of relevant parameters and Control Change
values. Allow sufficient time for processing to execute
(about 50 msec) before sending the P-85 another message.
When the XG System On message is received, the MIDI
system will be reset to its default settings.
The message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message
is sent.
XG Native Parameter Change message may contain two or
four bytes of parameter data (depending on the parameter
size).
[F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->
[00H] -> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H]
Data size must match parameter size (2 or 4 bytes).
[F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->
[bbH] -> [hhH] -> [mmH] -> [llH] -> [ddH] ->...->
[ccH] -> [F7H]
[F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->
[0nH] -> [ccH] -> [vvH] -> [F7H]
[4] P-85 Data List