Thank you for selecting Yamaha’s YST-M101 Powered Multimedia Speakers. Yamaha Active Servo Technology offers exceptionally high performance.

English

CAUTIONS

Please read the following operating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not following the cautions below.

cWhen you disconnect the AC adaptor from the AC receptacle, hold the adaptor itself and not the cord.

cIf you plan not to use YST-M101 for a while, disconnect the AC adaptor from the AC receptacle.

cAlways disconnect the AC adaptor from the AC receptacle before making any connections.

cYST-M101 does not contain any user serviceable parts. Refer all servicing to your Yamaha dealer.

cNever open the cabinet. If a foreign object drops into the set, contact your dealer and stop using YST-M101. Otherwise, you may cause a fire.

cThe voltage to be used must be the same as that specified on the rear panel. Using YST-M101 with a higher voltage than specified is dangerous and may cause a fire and/or electric shock.

cDo not expose YST-M101 to extreme temperatures, direct sunlight, excessive dust, humidity, or vibration.

cPosition YST-M101 on a level, stable surface. Do not drop, apply excessive force to their controls, or put heavy items on top of them.

cDo not place small metallic objects on YST-M101. Otherwise, the object may fall, possibly causing an injury.

cDo not place the following objects on YST-M101: Glass, china, etc.

If glass etc. falls by vibrations and breaks, it may cause personal injury.

A burning candle etc.

If the candle falls by vibrations, it may cause fire and personal injury.

A vessel with water in it

If the vessel falls by vibrations and water spills, it may cause damage to YST-M101, and/or you may get an electric shock.

cDo not place YST-M101 where foreign objects such as water drips might fall. It might cause a fire, damage to YST-M101, and/or personal injury.

cTo protect YST-M101, avoid microphone feedback, continuous and excessive output from electronic musical instruments, and excessive signal distortion.

cIf YST-M101 is located close to fluorescent or neon lights, a slight hum may be heard. In this case, relocate YST-M101 away from the light.

cAlthough YST-M101 is magnetically shielded, keep floppy disks and tapes away from it.

cAvoid sources of hum (transformers, motors). To prevent fire or electrical shock, do not expose to rain or water.

cWhen using a humidifier, be sure to avoid condensation inside YST-M101 by allowing enough spaces around YST-M101 or avoiding excess humidification. Condensation might cause a fire, damage to YST-M101, and/or electric shock.

cDo not use force on switches, knobs, or cables. When you move YST-M101, first turn off the power, then disconnect the AC adaptor from the AC receptacle and the cables from the connected devices.

cAlways set the POWER/VOLUME control fully to the left (in the standby mode) before starting to play the audio source: turn the control gradually after the play has started.

cBe sure to use the AC adaptor supplied with YST- M101. Otherwise, you might cause a fire or damage to YST-M101.

Standby mode

When YST-M101 is turned off by turning the POWER/ VOLUME control, YST-M101 consumes a small amount of power. This state is called the standby mode. The power supply is completely cut off from the AC line only when the AC adaptor is disconnected.

YST-M101 features a magnetically shielded design, but there is still a chance that placing it too close to a TV or a computer monitor might impair picture color. Should this happen, move YST-M101 away from the TV or the computer monitor.

CONNECTIONS

(See figure 1on page IV.)

Make connections between the speakers and other equipment as shown in the figure.

Caution: Plug in the right speaker and other equipment after all connections are completed.

E-1