Manuals / Yard-Man / Lawn and Garden / Lawn Mower

Yard-Man 503 Installing Front Wheels, Installing Rear Wheels, Removing Chute Retainer, Mower

Models: 503

1 16
Download 16 pages 62.29 Kb
Page 8
Image 8

Installing Front Wheels

• Lower the chute deflector carefully to its operating

• Place the front of the mower deck on raised blocks.

position keeping your fingers out of the way.

• Remove lock nut from pivot arm assembly, slide

 

 

 

 

 

 

 

wheel onto pivot arm assembly and secure with

 

 

 

 

 

 

 

lock nut. See Figure 6.

 

 

 

 

 

 

 

• Assemble the other side in the same manner.

Raise Chute

 

 

 

 

 

• If your mower is equipped with hub caps, place hub

 

 

 

 

 

Deflector

 

 

 

 

 

caps in position against the inner hub of wheel.

 

 

 

 

 

 

 

 

 

 

Remove

Press firmly around the center portion of the hub

 

 

 

 

 

 

 

 

 

 

Retainer

cap in a circular motion. The hub caps are flexible

 

 

 

 

 

 

 

 

 

 

 

 

and they will snap over the wheel hubs.

 

 

Figure 8

 

 

 

 

 

 

 

 

 

WARNING: The chute retainer must be

 

 

removed and discarded before operating

 

 

the mower.

 

 

 

 

 

Installing Mulching Baffle

 

 

 

 

 

If your mower is equipped with the optional mulching

 

baffle, install it on the right side of the deck following

 

these instructions. Make sure to follow the correct

 

sequence as indicated here.

 

 

 

Lock Nut

• Lift up and hold the side-discharge chute deflector.

• Insert bottom lip of the mulching baffle inside the

 

Pivot Arm

chute opening. See Figure 9.

 

 

Assembly

• Snap hooks of the mulching baffle over the hinge

Hub Cap (If Equipped)

pin of the chute deflector. See Figure 9. The hooks

Figure 6

must snap into place on the hinge pin, locking the

mulching baffle firmly onto the mower. For a close-

Installing Rear Wheels

up of the hinge pin location, see Figure 9 inset.

• Place the rear of the mower deck on raised blocks.

• Release the chute deflector.

 

 

• Remove lock nut from pivot arm assembly, slide

NOTE:

Install

bottom

lip

inside

chute

opening

wheel, with hollow side in, onto axle and secure

(indicated by 1 in the figure below) before placing hooks

with lock nut. See Figure 7.

over the hinge pin (indicated by 2 in the figure below).

• Assemble the other side in the same manner.

 

 

 

 

 

 

 

 

 

 

 

 

 

Hinge

 

 

 

 

 

 

 

Pin

 

Lock

Chute

Deflector

Nut

 

 

Hooks

Figure 7

Mulching

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Removing Chute Retainer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Baffle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The chute deflector on your mower is held in an upright

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

position by a retainer for shipping purposes only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remove the retainer, following steps below, before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

running the mower for the first time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chute

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Push the chute deflector up and towards the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

engine. Holding the deflector in this position,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

remove the retainer. See Figure 8.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lip of Mulching Baffle

 

 

 

 

 

 

 

 

(install inside chute opening)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 9

8

Page 7 Page 9
Page 8
Image 8
Yard-Man 503 manual Installing Front Wheels, Installing Rear Wheels, Removing Chute Retainer, Mower
Page 7 Page 9

503 specifications

The Yard-Man 503 is a powerful and versatile lawn mower that combines efficiency, durability, and ease of use, making it a popular choice for both residential and professional landscaping needs. This equipment is designed to tackle various types of terrain, from small suburban lawns to larger commercial properties, and it delivers consistent performance across a range of conditions.

One of the main features of the Yard-Man 503 is its robust engine. Equipped with a reliable four-stroke engine, this mower delivers enough power to cut through thick grass and weeds, ensuring a clean and precise cut every time. The engine's efficiency also means that operators can enjoy extended run times without the need for frequent refueling, making it ideal for larger tasks.

In terms of cutting technology, the Yard-Man 503 boasts a wide cutting deck that typically ranges from 20 to 30 inches, allowing for faster mowing and reduced cutting time. The adjustable cutting height feature is another highlight, enabling users to customize the length of grass to fit their preferences and the needs of their lawns. Whether you require a close trim or a longer cut for a healthier lawn, the Yard-Man 503 has you covered.

Ease of maneuverability is another characteristic that sets the Yard-Man 503 apart from its competitors. Its lightweight design, coupled with ergonomic handles, allows for easy navigation around obstacles and tight spaces. The mower’s self-propelled capabilities ensure that users can cover more ground with less effort, reducing fatigue during longer mowing sessions.

In addition, the Yard-Man 503 incorporates modern safety features, including a blade brake system, ensuring that the mower stops immediately when the operator releases the handle. This feature provides peace of mind, particularly for those with pets or children nearby.

The Yard-Man 503 is designed for durability, featuring a steel deck that withstands wear and tear over time. It is built to last, promising users a long lifespan and minimal maintenance needs. Its compact design also makes it easy to store in limited spaces, a practical consideration for many homeowners.

Overall, the Yard-Man 503 stands out in the lawn care market for its combination of power, user-friendly features, and robust construction, making it an ideal choice for anyone looking to maintain a pristine lawn efficiently and effectively.