POWER | ES700P | |
SUBWOOFER | ||
AMPLIFIER |
| SPEAKERS |
Left
Left
Right
Right
ONE SUBWOOFER PER SYSTEM
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ON POWER |
| T 3,15A GDC | ||
|
|
| T 5.0A 250V | |||
|
|
|
|
| SLO~BLO | |
230V |
|
| 120V | CAUTION: REPLACE WITH |
|
| SAME TYPE FUSE AND RATING | ||
50Hz |
|
| 60Hz |
|
1.3A | Yorkville | LR 21877 | 2.5A | ATTENTION: UTILISER UN FUSIBLE DE |
|
|
|
| RECHANGE DE MEME TYPE ET CALIBRE |
CAUTION AVIS |
L | R |
SPEAKER | SPEAKER |
POWER
ES700P AMPLIFIER ES700P
SUBWOOFERSUBWOOFER
TWO SUBWOOFERS PER SYSTEM
Yorkville |
| POWER |
|
| |
|
| HIGH |
| 125 Hz |
|
|
| FREQUENCY |
|
| |
ES700P | CUT OFF |
|
|
| |
DESIGNED & MANUFACTURED BY YORKVILLE SOUND • TORONTO, CANADA | 100 Hz |
| 150 Hz | ||
USER NOTE: |
| SUBWOOFER | +10 |
| |
| LEVEL | +3 | +20 | ||
This Subwoofer may be driven from Speaker Level | 0 |
|
|
| |
or Line Level signals. If an élite processor is used, |
|
|
|
| |
this Subwoofer should be plugged into the SUB |
|
|
|
| |
output of the processor. The |
|
|
| +30 | |
Cutoff should be set to |
|
|
| ||
should be set to LINE. For Line |
|
| dB |
| |
Level operation a balanced (Tip |
|
|
|
| |
Ring Sleeve) cable should be |
|
|
|
|
|
used. If the system is being | INPUT GROUND |
|
|
|
|
operated without a processor, | UNGROUNDED |
|
|
|
|
this Subwoofer can be | GROUNDED |
|
|
|
|
connected to the output of the | INPUT LEVEL |
|
|
|
|
power amplifier as shown in the |
|
|
|
| |
diagrams and the Input Level | SPEAKER |
|
|
|
|
should be set to SPEAKER. If | LINE |
|
|
|
|
none of the equipment has a U- |
|
|
|
|
|
ground, the INPUT GROUND |
|
|
should be set to GROUNDED. |
|
|
Otherwise the INPUT GROUND |
| I |
should be set to the position that | LEFT | |
best minimizes the hum. | N | |
| (mono) | P |
Refer to the Owner's | U | |
| T | |
Manual for other modes |
| |
|
| |
of operation |
|
|
PARALLEL
THRU
I
RIGHT NP
U
T
PARALLEL
THRU
Introduction
The ES700P is a premium quality integrated powered subwoofer and amplifier. Created as an
Configuration
The ES700P may be used in several different configurations, the minimum standard system is one ES700P used with a pair of full range speakers. The ES700P accepts the signal from separate Left and Right sources simultaneously. It then combines them into one signal (to drive the internal speakers). When used in a setup where only one signal is provided to a speaker, such as a mono system or stereo with more than one ES700P, use either the Left or Right input.
For normal operation connect the ES700P just like an ordinary speaker along with the full range speakers. The "INPUT LEVEL" switch should be set to "SPEAKER." If the audio source does not have a "U" ground, i.e.: a ground pin on the AC cord, the "INPUT GROUND" switch must be set to "GROUNDED" .The ES700P may be wired before or after the full range speakers. Use the left and right inputs when using a single ES700P in a stereo system. Use either the left or right inputs when using separate ES700P's for each side or when used in a mono system. The ES700P does not alter the signal to the full range speakers in any way. The ES700Pwill not draw any power from the amplifier driving the full range speakers. Please note that an external
