Manuals / Zanussi / Kitchen Appliance / Dishwasher

Zanussi DA 4342 manual Hints for test centres, Adjusting the worktop, Fitting under a counter

Models: DA 4342

1 26

Download 26 pages 42.35 Kb

Page 7

Adjusting the worktop

Adjusting the worktop

You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units.

Simply unscrew the two front retaining screws, move the top to the required position and then retighten the screws.

Fitting under a counter

(kitchen worktop or sink)

By removing the machine’s worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture.

Proceed as follows:

-Remove the machine’s worktop by unscrewing the

two front retaining screws, pull from the front and slide out the rear slots, lifting the worktop.

Insert the machine after adjusting height and levelling with the adjustable feet (see Instruction book - Part 1).

When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed.

IN02

570-

600

820

450

IN04

Hints for test centres

Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispe			nser

Test standard:	EN	50242

Reference programme:	ECONOMY	50°C

Load:		9 standard place settings

Rinse aid selector:	position	4

Detergent dosage:	20 g in	the dispenser
		5 g on the dispenser lid

US65

Arrangement upper basket

UI61

Arrangement lower basket

7

Image 7

Zanussi DA 4342 manual Hints for test centres, Adjusting the worktop, Fitting under a counter, Proceed as follows

Contents

INSTRUCTION BOOK DISHWASHER DA152977 35/2 Description of the appliance 1. ON-OFF indicator light 2. ON-OFF push button6. Programme sequence indicator 3. ECONOMY 50 push button 4. Salt refilling indicator lightDegree of soil Technical specificationsWashing programmes Type of load2. Check that there is rinse aid and salt 10. Switch off the dishwasherOperating sequence 1. Check the filtersThe cutlery basket Using your applianceLoading your appliance The lower basketBefore closing the door, ensure that the spray arms can rotate freely Adjusting the height of the upper basketThe upper basket To move to the higher position proceed as followsProceed as follows Adjusting the worktopHints for test centres Fitting under a counterCustomer Care Department Service and spare parts08705 This guarantee does not cover Guarantee conditionsStandard guarantee conditions European Guarantee2 09/01 From the Electrolux Group. The world’s No.1 choiceImportant safety information ContentsBefore use Maintenance Installation Safety instructionsConservation Important safety informationInstallation Child SafetyAdjustment on the machine Setting the water softenerBefore using your dishwasher for the first time Water softener adjustmentmay cause corrosion refill indicator windowB A salt indicator light Filling with saltFilling with rinse aid Adjusting the doseOnly for dishwasher models with rinse aid indicator light Rinse aidCompact detergents with enzymes If using powder detergents proceed as followsIf using detergent in tablets proceed as follows Use of detergentItems not suitable for dishwashers Hints and tipsTo save energy For best washing and drying resultsFinish Dishwasher Cleaner Maintenance and cleaningInternal cleaning Cleaning the filtersMoving the machine External cleaningFrost precautions Prolonged periods of non-operationThe machine will not start SymptomThe dishes are not clean Something not workingRA01 Always insist on genuine spare partsRemove all packaging before positioning the machine InstallationLevelling Water supply connectionsThe end of the drain hose can be connected in the following ways Water outlet hose connectiondraining of your dishwasher We advise you therefore to remove it 2. Hooked over the edge of the sink using the specialThis appliance must be earthed Electrical connectionProceed as follows CE03Page 1 09/01