Parts Required, Levelling the Appliance | Zanussi ZCG 7902X specification

INSTALLATION

1. PARTS REQUIRED

The loose hotplate parts are packed in the polystyrene fitment on top of the hotplate.

2. LEVELLING THE APPLIANCE

If the appliance requires levelling or its height adjusting (from the hotplate to any working surface), the procedure below must be followed:

1.Adjustment to suit floor conditions or height is obtained by rotating clockwise or anticlockwise the feet, at the front and rear of the appliance.

2.A spirit level should be placed on one of the oven shelves to confirm the appliance is correctly levelled.

3.FITTING THE STABILITY BRACKET

It is recommended that if the appliance is to be installed with a flexible supply pipe a stability bracket (SK.4729.A) is fitted and is available from your supplier (see Important Safety Requirements). These instructions should be read in conjunction with the leaflet packed with the stability bracket.

1.Place the appliance in its intended position and level appliance.

2.Mark off 300mm from the left hand side of the appliance as shown in dimension 'A', Fig 2a. This is the centre line of the fixing bracket.

3.Draw a line 100mm from the front edge of the levelling feet (see Fig.2a) and remove appliance from its position. Mark off dimension 'B' (see Fig.2a) back from this line on the centre line of the bracket to locate the front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then measure the height from floor level to engagement edge on back of appliance, dimension 'C' of Fig.2b.

4.Assemble upper bracket to lower bracket so that underside of bracket is dimension 'C' +3mm above floor level.

Reposition appliance and check that top bracket engages into appliance back as shown in Fig. 2b.

487mm (B)

100mm

(A)

300mm

(C)

Fig.2a

Fig.2b

47

Image 47

Zanussi ZCG 7902X manual Parts Required, Levelling the Appliance, Fitting the Stability Bracket

Contents

ZCG Introduction For your safety Contents Hotplate Lighting the appliance Second oven Grill/second ovenGrill Oven light Main ovenTo turn off any burner Heat control Prior to using the grillGrill control has two heat settings Grill Positioning food on the grid Cooking positionsGeneral Preheating Grill pan is supplied with a removable handle Grill pan and handle Burner sizes Hotplate Than pans which are warped Take care to avoid burns and scalds when youAre reaching across the hotplate Use pans with flat bases. They are more stable Helpful hints Oven shelves OvensHeat zones Baking trays and dishes Condensation Roasting Oven cooking chart Main oven Mins. per ½kg 1lb and 25 mins 30 40 mins Base Well Done Oven cooking chart Second ovenBase Medium Lamb Shelf on Medium Fruit pie shortcrust 25 35 mins Baked custard 50 60 mins 45 60 mins Turn the selector knob to Manual then turn to Clock Electronic timerTo use the Timer To set the time of day Clock. Turn Setting the controls for automatic useAutomatic control Showing Selector knob to Correct time? What time do Turn the selector knob to You want Cooked by? Switch off showsG 7 9 0 2 How long will Turn the selector knob to Food take To cook? Hints and tips for automatic cooking Please note There is no slow cook on the second oven Slow cookingFood preparation slow cooking Left over food should be cooled quickly and refrigerated Do not cook casseroles over 2.7kg 6lbCover food with a tight fitting lid or tin foil Thaw thoroughly before cooking Cleaning the handles and control knobs Care and cleaning For your safety Cap to crown When replacing hotplate burner parts Grill and oven furniture Ovens Main oven cleaning cycle Some staining will remain Top oven cleaning cycle To remove the outer glass Cleaning between the outer and inner door glass Make sure that a stability bracket is fitted Cleaning The Door GlassInstalling the appliance Location Width 598mm Depth Appliance dimensionsPositioning Height to hotplate 900mm 920mm Moving your appliance General information For your safetyConnecting to the electricity supply Replacing the oven light bulb Check What is wrong and why? Probably a fault 7 0 5 9 2 9 9 2 Service and spare parts Customer Care Department Installation Instructions Hotplate DimensionsConnections Grill General Important Safety RequirementsMain Oven Second Oven Location of Appliance Fitting the Stability Bracket Parts RequiredLevelling the Appliance Connection to the Electricity Supply Connecting to GAS Checking LID SHUT-OFF Device Pressure TestingChecking the Grill Checking the Hotplate Automatic Operation Checking the Main Oven ControlsChecking the Main Oven General Note Checking the Second OvenChecking the Main Oven Light Standard guarantee conditions Guarantee Conditions T E S G 7 9 0 2 T E S Part Number311650801