Operating sequence

1. Check the filters

Ensure they are clean and properly positioned (see "Maintenance and cleaning").

2. Press the On/Off push button

The display will show the last selected programme.

3. Check that there is rinse aid and salt

The corresponding indicator lights will illuminate if refilling is necessary.

4. Load the dishes

Remove any scraps of food.

Pull the lower basket out and arrange the saucepans, plates and cutlery in it.

Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. in it.

Slide the baskets back into the machine.

5.Ensure that the spray arms can rotate freely

6.Measure out detergent

Add the required amount of detergent into the dispenser.

Important!

If you select the half load option remember to reduce the quantity of detergent.

Close the detergent dispenser lid.

7a. Setting and starting the programme without "Delay start"

The selection of the programme occurs with the door partially opened.

Press the "

programme selection

 

" push button until the

required programme number appears in the digital

 

display.

 

 

 

 

 

If you wish to see the duration of the programme you

 

have just selected,

ONLY with the door opened

, press

the Cancel

push button.

 

 

 

Select a

drying option

 

and/or

half load

(if desired).

Close the door, the programme will start automatically and an audible signal advises you of that.

The display will show the running time of the programme.

7b. Setting and starting the programme with "Delay start"

Once a programme and required options (see point 7a)

 

have been selected to use

Delay start

proceed as

follows:

 

 

 

Press the

Delay start

push button. The digital display

will show "h 0". Press the button again to select the

 

number of hours by which you wish to delay the

 

programme start (up to a maximum of 12 hours).

 

If the a drying option and/or half load have been

 

selected the corresponding indicator lights will turn off,

 

but don’t worry, the delay start will not modify the

 

settings made previously .

 

 

To set the time setting to zero press the

Delay start

push button until "h 0" appears in the digital display.

 

Close the door, the countdown will start automatically and an audible signal advises you of that.

The start of the programme is shown in the digital display and will decrease from hour to hour.

The progression of the countdown will be confirmed by a flashing dot after the number in the digital display. The opening of the door will not stop the countdown. Once the delayed time has elapsed the programme will start automatically and in the digital display will appear the duration of the programme.

 

To cancel a delay start in progress,

open the door and

 

press the

Cancel

push button. The delay start will be

 

cancelled without modifying the previous selection of the

 

 

washing programme with relative options. In the digital

 

 

display will appear the number of the programme.

 

8.

To cancel a programme in progress

 

 

Open the door and press the

Cancel

push button.

An audible signal will inform you that the programme has been cancelled and in the digital display first will appear

three horizontal lines ---(for about 2 seconds) and then the number of the programme just cancelled.

The dishwasher has returned to setting mode and it is now possible to select a new washing programme.

9. At the end of the washing programme

The dishwasher will automatically stop and an intermittent audible signal will be heard when the programme has ended (when the delay start has been selected the audible signal "end of programme" is automatically excluded).

3 flashing horizontal lines will appear in the digital display and all the indicator lights will turn off. Open the door and press the On/Off push button.

Wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one.

Important!

In general it is not advisable to open the door while the machine is working; if the door is opened however, a safety device ensures that the machine stops.

Care must be taken if the door is opened during the hot phase or immediately after a programme has finished, as steam may escape.

When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off.

11

Page 11
Image 11
Zanussi ZDT 6894 manual Operating sequence