Zebra Technologies MIX05120 instruction sheet Thank You For Your Support Of Our Products

Zebra Skimmers Corp. MIX05120

Zebra® Economy Mixer Manual

Package Contains:
1.	Drum proportioner	4.	Metering tip kit (14 tips)
2.	Suction tube (4 ft.) with foot valve	5.	Product information sheet

3.Discharge tube (4 ft.) max length for delivery

THANK YOU FOR YOUR SUPPORT OF OUR PRODUCTS

Please use this equipment carefully and observe all warnings and cautions.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - NOTE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

WEAR	protective clothing and eyewear when dispensing chemicals or other materials.
ALWAYS	observe safety and handling instructions of the chemical manufacturers.
ALWAYS	direct discharge away from you or other persons or into approved containers.
ALWAYS	dispense cleaners and chemicals in accordance with manufacturer’s instructions. Exercise CAUTION when maintaining your equipment.
CLEAN	equipment after each use in accordance with instruction sheet.
WEAR	protective clothing and eyewear when working in the vicinity of all chemicals, filling or emptying equipment or changing metering tips.
ALWAYS	re-assemble equipment according to instruction procedures. Be sure all components are firmly screwed or latched into position.
ATTACH	only to tap water outlets (75 PSI maximum).

Installation and Operation:

1.Select a metering tip (see next section), and insert it into the suction stub. Slide the open end of the suction tube through the bung adaptor, then over the suction stub.

2.Slide end of discharge tube over the eductor discharge outlet.

3.Remove either the 3/4 or 2-inch bung from an upright drum.

4.Insert the foot valve end of the suction tube into the drum.

5.Swivel the drum adapter several turns in the bung opening until the bracket is secure.

6.Install minimum 1/2-inch ID water hose between the inlet swivel and water supply spigot. (Minimum 25 PSI flowing water pressure is required to operate the unit.)

7.Turn on water supply. To begin dispensing solution, open ball valve at inlet to unit. Do not keep discharge hose in liquid! The concentrate will siphon from the container.

Metering Tip Selection:

The final concentration of the dispensed liquid is related to both the size of the metering tip opening (orifice) and the viscosity of the liquid being siphoned. If product viscosity is noticeably greater than that of water, consult the procedure for Measurement of Concentration on the next page to achieve your desired water-to-product ratio. For waterthin products, use

the chart below as a guideline. Because such factors as inlet water pressure and temperature can affect dilution ratios, the figures listed below are only approximate. Test the actual dilution you are achieving using the Measurement of Concentration procedure for best results. Two undrilled, clear tips are supplied for drilling sizes not listed.

		Decimal	Approximate Dilution Ratio at
Tip Color	Drill Size	Equivellent	40 PSI, water-thin viscosity (1.0 cp)
No tip			4.5:1	or 22.2%
Gray	30	.1285	5:1	20.0
Black	40	.0980	6:1	16.6
Beige	50	.0700	9:1	11.1
Red	55	.0520	20:1	5.0
White	57	.0430	24:1	4.16
Blue	60	.0400	26:1	3.84
Tan	65	.0350	31:1	3.23	Copyright 2008
Green	70	.0280	50:1	2.0	Zebra Skimmers Corp.
Orange	72	.0250	70:1	1.43	PO Box 833
Brown	74	.0225	90:1	1.11	Chagrin Falls, OH 44022
Yellow	76	.0200	100:1	1.0	888-249-4855
					www.ZebraSkimmers.com
Purple	80	.0135	200:1	.50
Pink	87	.0100	400:1	.25	Printed in the USA • Revised February 2008