[BC3501LE/WE/BC4501WE]

•Using attached 4 socket screws, secure the connection firmly with equal force.

■HANDLE [BC2311LE/BC2611LE/BC3501LE]

• Put the handle onto the main pipe and fix it with 4 screws.

[BC2611WE/BC3501WE/BC4501WE]

1.Loosen the 4 bolts on the upper cap and insert the handles equally. Retighten the bolts.

2.Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely.

[BC2611WE] [BC3501WE/BC4501WE]

■CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor.

1.2.

■CONNECTING SWITCH WIRES

•Connect the switch wires between the engine and the main unit.

■PROTECTOR [BC2611WE/BC3501WE/BC4501WE]

• Wrap the protector around the outer pipe as shown in the figure, and fasten the magic fastener.

■INSTALLING DEBRIS GUARD

1.Fit the guard skirt on debris guard.

2.[BC2311LE/BC2611]

Attach the debris guard with the bolts provided while inserting the spacer between the guard and the pipe.

[BC3501/BC4501WE]

Attach the debris guard with the bolts provided to the pipe.

Guard skirt

for line head only

Spacer

BC2311LE/BC2611 only

■INSTALLING LINE HEAD

1.While locking the gear shaft by inserting the angled bar(1) into the holder(A)(2) on the gear box, loosen and remove the nut(left-handed)

2.Fit the line head assembly to the gear shaft. Tighten it securely by hand.

■INSTALLING BLADE

Remove the guard skirt of debris guard, when using metal blade.

1.Put the angled bar(1) into the side holes of the inner holder and the gearcase.

2.Remove the nut(Left-handed) and the outer holder(3) from the gearshaft.

3.Put the blade onto the inner holder(2). Make the marked side face the holder.

4.Put the outer holder(3) onto the gearshaft making the recessed side face the blade.

5.Fasten the blade by the nut and the cover(4).

■BALANCE UNIT

1.Put on strap and attach unit to strap.

2.Slide clamp up or down until unit balances with head aparting from the ground when using it.

4

Fuel

WARNING

•Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

(when using ZENOAH genuine oil)

•The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

•Do not use BIA or TCW (2-stroke water-cooling type) mixed oil.

•Exhaust emission are controlled by the fundamental engine parameters and components (eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

•These engines are certified to operate on unleaded gasoline.

•Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

•If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

•Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

•Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

■HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

■FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 10feet (3meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1.FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.

5.In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to fhe mixed gasoline, etc. described therein, if may not be covered by the warranty.

5 Operation

■STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1.Feed fuel into the fuel tank and tighten the cap securely.

2.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine.

3.Push the primer pump several times until overflown fuel flows out in the clear tube.

(1)Choke lever

(2)Close

(3)Open

(4)Primer pump

Page 1 Page 3
Page 2
Image 2
Zenoah BC3501LE/WE, BC2611LE/WE, BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, BC4501WE owner manual Operation
Page 1 Page 3

BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, BC4501WE, BC2611LE/WE, BC4501WE, BC2311LE, BC3501LE/WE specifications

The Zenoah BC series of brushcutters represents a culmination of advanced engineering, ergonomic design, and powerful performance. Among the prominent models in this series are the BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, and BC4501WE. Each model is tailored for specific user needs, ensuring efficiency and reliability in various cutting tasks.

The BC2311LE is designed for lightweight performance, making it ideal for residential users and small garden maintenance. Its compact design is paired with an efficient engine that provides ample power while minimizing fuel consumption. This model is perfect for trimming grass around flower beds and edging along walkways.

Stepping up in power, the BC2611LE offers a balance between weight and performance. It is designed for homeowners and professionals who require greater durability and cutting ability. Equipped with a high-torque engine, this model excels in tackling thicker vegetation and heavy-duty landscaping tasks.

The BC2611WE variant incorporates advanced technologies such as a low-emission engine and easy-start systems, further enhancing user experience. This model also features a robust construction that withstands rigorous use, making it suitable for commercial applications.

For those needing even more power, the BC3501LE and BC3501WE models are engineered for heavy-duty operations. The BC3501LE focuses on efficient performance with a user-friendly design, while the BC3501WE adds versatility with its increased user comfort and reduced vibrations, ensuring prolonged usage without fatigue.

The BC4501WE is the flagship model in the series, delivering unparalleled power and performance for the most demanding tasks. Its advanced engine technology not only boosts power output but also ensures compliance with stringent environmental regulations, making it a responsible choice for professionals.

One of the standout characteristics across the Zenoah BC series is their cutting-edge anti-vibration technology. This feature significantly reduces operator fatigue, allowing users to work longer hours with greater comfort. Additionally, the ergonomic handles and lightweight construction contribute to improved control and maneuverability.

Each model in the Zenoah BC series is designed with durability in mind, incorporating high-quality materials that stand up to the rigors of outdoor work. Whether for residential yards or professional landscaping, these brushcutters embody efficiency, power, and advanced design, making them a reliable choice for any user. The Zenoah BC series, including models like the BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, and BC4501WE, is truly a testament to engineering excellence and user-focused design.
Top Page Image Contents