The indicator of the effect module currently selected for editing is flashing.

NOTE

The EQ module cannot be switched off. To disable this module, set all parameters (PARAM 1 through PARAM 4) to the value "5".

NOTE

With each push of the MODULE SELECT▲key, the

edited module moves one position to the right. When the

 

 

REV/DLY module is reached, the cursor loops back to

 

the COMP&WAH module.

MODULEMODULEMODULEMODULEMODULEMODULE

COMP

DIST

 

EQ

 

CHO

 

REVERB

COMP

WAH

 

 

FLG

 

DELAY

WAH

 

 

 

 

 

3.Next, use the PARAM SELECT ▼ key to select the parameter within that module that you wish to edit.

The indicator of the selected parameter is flashing.

HINT The pedals 1 – 3 and the BANK pedal correspond to the following effect modules:

•BANK pedal: COMP&WAH

•Pedal 1: DISTORTION

• Pedal 2:

CHO/FLG

• Pedal 3:

REV/DLY

The effect module ON/OFF setting can also be stored as part of a patch.

Storing a Patch

NOTE

With each push of the PARAM SELECT key, the selected parameter moves one position down. When PARAM 4 is reached, the cursor loops back to PARAM 1.

 

PARM

PARM

1

 

 

PARM

PARM

2

 

PARM

PARM

3

 

PARM

PARM

4

 

PARM

If an edited patch is not stored, the change will be lost when another patch is selected. To preserve a setting, store the patch as described below.

1.Press the STORE key in the Edit mode.This activates the store standby condition.

HINT Storing is possible also in the Play mode.

PARM

1

HINT The value of the selected effect parameter is shown on the display. If the display shows only "- - ", the effect module is OFF. Set the effect module to ON before editing, as described on page 8.

4.Use the VALUE +/- keys to change the parameter value.

HINT For details on the parameters of each effect module, please refer to "Effect Types and Parameters" on pages 9

2.Choose the bank and patch number in which you want to store the patch.

Use the BANK pedal to first select the bank and then specify the patch number with the pedals 1 – 3.

NOTE Patches cannot be stored in the PRESET group. If a patch was chosen from the PRESET group, the store destination will automatically become the USER group.

Specify a bank and patch number in the USER group.

NOTE

– 12.

Parameter setting changes made in this way are only temporary. If you return to the Play mode or select a different patch without storing the new settings first, the settings will be lost.

3. If no bank and patch number is specified for a patch
selected from the USER group, the patch will be stored
in the original location.
If no bank and patch number is specified for a patch
selected from the PRESET group, the patch will be stored
For details on how to store a patch, please refer to the explanation at right.Switching Effect Modules On and OffIn the Edit mode, effect modules can be turned on and off independently.

1.Pressing a pedal corresponding to an effect module that is currently on (module cursor indicator lit) turns the effect module off. The indicator goes out.

2.Press the pedal again to turn the effect module back on.
in "A1" of the USER group.

HINT When a patch is stored, the patch that was previously stored in that number will be overwritten (erased). Take

care not to erase a patch that you want to keep. When wishing to restore all factory preset patches, please refer to "Reinitializing the 1010 (Special Mode)" on page 13. Restoring individual patches is not possible.

4.Press the STORE key again. The patch is stored, and the 1010 reverts to the Play mode.

NOTE

If the STORE key has not yet been pressed for the second

time, you can use the EDIT key to cancel the store

 

 

process and return to the Play mode.

8