Husqvarna YTH22V42 owner manual Tractor, Blade Care, Blade Removal See Fig, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 13)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 13

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 14)

•Raisemowertohighestpositiontoallowaccesstoblades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

Fig. 14

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Raise seat.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 917.289620 Safe Operation Practices for Ride-On Mowers General OperationII. Slope Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unpack Carton Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsSchedule MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Deck Washout Port See Fig CleaningMuffler IN-LINE Fuel Filter See FigTo Remove Mower See Fig To Install Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel See FigTransmission Cylinders OtherFuel System Engine OILProblem Cause Correction TroubleshootingEngine continues Tractor - Model Number YTH22V42 SchematicElectrical KEY Part Description Chassis Tractor - Model Number YTH22V42 Drive Washer Harden .793 x 1.637 x Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH22V42 Mower Deck KEY Part NO. no Description 100 101 Mower LiftSeat Assembly Wheels and Tires DecalsLiquid Gasket and the Breather Gasket are Interchangeable Briggs Engine Model Number 407777, Type Number 1195-B1Tractor - Model Number YTH22V42 125 163 141 231 108 633 1342 1353 276 160 947 KEY Part Description Tractor - Model Number YTH22V42 Model K46BT KEY Part Description Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation05.05.10 JA
Related manuals
Manual 44 pages 20.69 Kb Manual 56 pages 31.28 Kb

YTH22V42 specifications

The Husqvarna YTH22V42 is a versatile and robust riding mower designed to meet the needs of homeowners looking for efficiency and durability in lawn care. This model is equipped with a powerful 22-horsepower Kohler engine, delivering reliable performance and enabling easy handling of various terrains. With its automatic transmission, operators can simply push a pedal to control the speed, providing a smooth and enjoyable mowing experience.

One of the standout features of the YTH22V42 is its 42-inch cutting deck, which allows for a wide cutting path, making it suitable for medium to large-sized yards. The cutting deck is reinforced, ensuring longevity and durability, while its air induction technology enhances airflow for a clean and even cut. The cutting height can be easily adjusted with a lever, offering six different settings from 1 to 4 inches.

Another significant characteristic of the YTH22V42 is its ease of use. The ergonomic design of the seat and steering wheel enhances comfort during longer mowing sessions. The mower is equipped with intuitive controls that make it easy for users of all experience levels to operate. Additionally, the unit features built-in anti-scalp wheels to protect the lawn from damage while trimming.

The Husqvarna YTH22V42 also boasts several innovative technologies. The ReadyStart system ensures an easy, no-prime starting of the engine, significantly reducing preparation time before mowing. The mower's compact design allows for easy maneuverability in tight spaces, making it effective for navigating around landscaping or garden features.

Furthermore, the YTH22V42 is compatible with Husqvarna’s extensive range of accessories, enhancing its versatility. From mulching kits to rear baggers, users can customize their mowing experience according to their specific lawn care needs.

In terms of maintenance, the YTH22V42 features a deck washout port, which simplifies cleaning under the cutting deck after use, prolonging the mower's lifespan and ensuring consistent performance. Additionally, the mower's robust construction ensures it can withstand the rigors of regular use.

Overall, the Husqvarna YTH22V42 combines power, comfort, and technology, making it an excellent choice for homeowners seeking a reliable and efficient riding mower. Its thoughtful design and advanced features position it as a leading option in the market, perfect for those looking to maintain a beautiful lawn with ease.
Top Page Image Contents