Husqvarna YTH22V42 To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 30)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "TO INSTALL MOWER" in this section of manual).

MANDRELIDLER

PULLEYPULLEYS

MANDREL

PULLEY

Fig. 30

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 31)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler (A) and clutching idler (B).

•Remove belt from centerspan idler (C).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

•Remove belt downward from engine pulley (E).

•Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

•Pull belt toward front of tractor and roll belt onto engine pulley (E).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (C).

•Install belt through stationary idler (A) and clutching idler (B).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” section in this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

Fig. 31

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 917.289620 Safe Operation Practices for Ride-On Mowers General OperationII. Slope Operation General Service ServiceIII. Children IV. TowingTable of Contents Toremovetractorfromcarton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo USE Cruise Control J See Fig To Operate MowerUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningIN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Remove Mower See Fig To Install Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System OtherEngine OIL CylindersProblem Cause Correction TroubleshootingEngine continues Tractor - Model Number YTH22V42 SchematicElectrical KEY Part Description Chassis Tractor - Model Number YTH22V42 Drive Washer Harden .793 x 1.637 x Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH22V42 Mower Deck KEY Part NO. no Description 100 101 Mower LiftSeat Assembly Wheels and Tires DecalsLiquid Gasket and the Breather Gasket are Interchangeable Briggs Engine Model Number 407777, Type Number 1195-B1Tractor - Model Number YTH22V42 125 163 141 231 108 633 1342 1353 276 160 947 KEY Part Description Tractor - Model Number YTH22V42 Model K46BT KEY Part Description Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation05.05.10 JA
Related manuals
Manual 44 pages 20.69 Kb Manual 56 pages 31.28 Kb

YTH22V42 specifications

The Husqvarna YTH22V42 is a versatile and robust riding mower designed to meet the needs of homeowners looking for efficiency and durability in lawn care. This model is equipped with a powerful 22-horsepower Kohler engine, delivering reliable performance and enabling easy handling of various terrains. With its automatic transmission, operators can simply push a pedal to control the speed, providing a smooth and enjoyable mowing experience.

One of the standout features of the YTH22V42 is its 42-inch cutting deck, which allows for a wide cutting path, making it suitable for medium to large-sized yards. The cutting deck is reinforced, ensuring longevity and durability, while its air induction technology enhances airflow for a clean and even cut. The cutting height can be easily adjusted with a lever, offering six different settings from 1 to 4 inches.

Another significant characteristic of the YTH22V42 is its ease of use. The ergonomic design of the seat and steering wheel enhances comfort during longer mowing sessions. The mower is equipped with intuitive controls that make it easy for users of all experience levels to operate. Additionally, the unit features built-in anti-scalp wheels to protect the lawn from damage while trimming.

The Husqvarna YTH22V42 also boasts several innovative technologies. The ReadyStart system ensures an easy, no-prime starting of the engine, significantly reducing preparation time before mowing. The mower's compact design allows for easy maneuverability in tight spaces, making it effective for navigating around landscaping or garden features.

Furthermore, the YTH22V42 is compatible with Husqvarna’s extensive range of accessories, enhancing its versatility. From mulching kits to rear baggers, users can customize their mowing experience according to their specific lawn care needs.

In terms of maintenance, the YTH22V42 features a deck washout port, which simplifies cleaning under the cutting deck after use, prolonging the mower's lifespan and ensuring consistent performance. Additionally, the mower's robust construction ensures it can withstand the rigors of regular use.

Overall, the Husqvarna YTH22V42 combines power, comfort, and technology, making it an excellent choice for homeowners seeking a reliable and efficient riding mower. Its thoughtful design and advanced features position it as a leading option in the market, perfect for those looking to maintain a beautiful lawn with ease.
Top Page Image Contents