Husqvarna YTH22V42 To Remove Wheel See Fig, Front Wheel TOE-IN/CAMBER, Replacing Battery See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 32

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

Fig. 33

REPLACING BATTERY (See Fig. 34)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

•Lower seat pan.

SEAT PAN

 

TERMINAL

NUT

COVER

BOLT

 

POSITIVE

NEGATIVE

(RED)

(BLACK)

CABLE

CABLE

02603

 

Fig. 34

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 917.289620 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Before Removing Tractor from Skid Tools Required for AssemblyToremovetractorfromcarton Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningMuffler Deck Washout Port See FigTo Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL OtherFuel System CylindersTroubleshooting Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH22V42Electrical KEY Part Description Chassis Tractor - Model Number YTH22V42 Drive Washer Harden .793 x 1.637 x Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH22V42 Mower Deck KEY Part NO. no Description Mower Lift 100 101Seat Assembly Decals Wheels and TiresBriggs Engine Model Number 407777, Type Number 1195-B1 Liquid Gasket and the Breather Gasket are InterchangeableTractor - Model Number YTH22V42 125 163 141 231 108 633 1342 1353 276 160 947 KEY Part Description Tractor - Model Number YTH22V42 Model K46BT KEY Part Description Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX05.05.10 JA
Related manuals
Manual 44 pages 20.69 Kb Manual 56 pages 31.28 Kb

YTH22V42 specifications

The Husqvarna YTH22V42 is a versatile and robust riding mower designed to meet the needs of homeowners looking for efficiency and durability in lawn care. This model is equipped with a powerful 22-horsepower Kohler engine, delivering reliable performance and enabling easy handling of various terrains. With its automatic transmission, operators can simply push a pedal to control the speed, providing a smooth and enjoyable mowing experience.

One of the standout features of the YTH22V42 is its 42-inch cutting deck, which allows for a wide cutting path, making it suitable for medium to large-sized yards. The cutting deck is reinforced, ensuring longevity and durability, while its air induction technology enhances airflow for a clean and even cut. The cutting height can be easily adjusted with a lever, offering six different settings from 1 to 4 inches.

Another significant characteristic of the YTH22V42 is its ease of use. The ergonomic design of the seat and steering wheel enhances comfort during longer mowing sessions. The mower is equipped with intuitive controls that make it easy for users of all experience levels to operate. Additionally, the unit features built-in anti-scalp wheels to protect the lawn from damage while trimming.

The Husqvarna YTH22V42 also boasts several innovative technologies. The ReadyStart system ensures an easy, no-prime starting of the engine, significantly reducing preparation time before mowing. The mower's compact design allows for easy maneuverability in tight spaces, making it effective for navigating around landscaping or garden features.

Furthermore, the YTH22V42 is compatible with Husqvarna’s extensive range of accessories, enhancing its versatility. From mulching kits to rear baggers, users can customize their mowing experience according to their specific lawn care needs.

In terms of maintenance, the YTH22V42 features a deck washout port, which simplifies cleaning under the cutting deck after use, prolonging the mower's lifespan and ensuring consistent performance. Additionally, the mower's robust construction ensures it can withstand the rigors of regular use.

Overall, the Husqvarna YTH22V42 combines power, comfort, and technology, making it an excellent choice for homeowners seeking a reliable and efficient riding mower. Its thoughtful design and advanced features position it as a leading option in the market, perfect for those looking to maintain a beautiful lawn with ease.
Top Page Image Contents