Husqvarna CTH2542 XP To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 27

SERVICE AND ADJUSTMENTS

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 34

TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 35

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 36)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

02141

FIG. 36

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents CTH2542 XP II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Key Slope Sheet Unassembled PartsSteering Wheel SeatBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig To Install Bagger Components toTractor See Figs A-4D To Assemble Bagger See Figs A-5C Bagger Adjustment SeeHorizontal Adjustment Vertical AdjustmentTo Assemble and Install Mulcher Plug See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS See FigTo Operate Mower See Fig Service REMINDER/HOUR Meter To Operate on HillsTo Transport See Figs To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsTo Dump Bagger See Bagging SeeTo Convert Mower See Before Each USE MaintenanceLubrication Chart General RecommendationsCheck Operator Presence System TractorBlade CARESee Figs.20-22 Star Pattern BladeEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER Interlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch TRACTOR- -MODEL NO. CTH2542XP 96061015900, Product no 61 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 17 Control Throt 532 18 Seat Seat AssemblyWheels & Tires DecalsMower SVC CRDMower Lift Bagger Service Notes Service Notes Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 40 37-50 Rev 04.25.06 VB/TR

CTH2542 XP specifications

The Husqvarna CTH2542 XP is a robust riding lawn mower designed to cater to the needs of homeowners with mid-sized lawns. This machine is engineered for precision, efficiency, and exceptional comfort, making lawn care a seamless task.

One of the standout features of the CTH2542 XP is its powerful 24-horsepower Kohler engine. This reliable engine delivers ample power to tackle tough grass and uneven terrain. Paired with hydrostatic transmission, the mower offers smooth acceleration and easy control, making it simple to navigate various yard conditions.

Equipped with a 42-inch cutting deck, the CTH2542 XP allows for efficient mowing across medium to large lawns. The deck is made from high-quality materials, ensuring durability and longevity. Its cutting height can be easily adjusted between different positions, allowing users to customize their lawn’s appearance as per their preference.

The mower is designed with user comfort in mind. It features an ergonomic seat with armrests, providing support during extended mowing sessions. The easy-to-reach controls facilitate effortless maneuvering, reducing fatigue while working. Moreover, the compact design of the CTH2542 XP allows it to fit through tight spaces, making it versatile for various yard layouts.

In terms of technology, the CTH2542 XP includes a variety of innovative features. The air induction mowing technology optimizes airflow within the deck, ensuring an even cut and eliminating clumping. Additionally, the mower is compatible with a range of accessories, allowing users to tailor their equipment for mulching, bagging, and other functions.

Another notable characteristic of the CTH2542 XP is its robust build quality. Constructed with a heavy-duty frame and components, it can withstand the rigors of lawn care, ensuring it remains a reliable companion for years.

Finally, Husqvarna’s commitment to environmental sustainability is reflected in the design of the CTH2542 XP. The machine is engineered for fuel efficiency, minimizing emissions while delivering excellent performance, making it a responsible choice for eco-conscious consumers.

In conclusion, the Husqvarna CTH2542 XP stands out due to its powerful engine, user-friendly features, and innovative technology. It is designed for homeowners who seek a balance between performance and ease of use, making lawn maintenance a more enjoyable endeavor. Whether mowing a large lawn or navigating tight spaces, the CTH2542 XP proves to be a versatile and reliable tool for maintaining a beautiful yard.
Top Page Image Contents