Husqvarna CTH180 XP owner manual To Install Bagger Components to Tractor See Figs A-4D

Page 8

ASSEMBLY

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

TO INSTALL BAGGER COMPONENTS TO TRACTOR (See Figs. 4A-4D)

•Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor.

•Remove the two (2) 3/8 nuts and fl at washers from the bolts at the tractor back plate.

DISCHARGE

CHUTE

3/8 NUT

FLATWASHER

0 2277

FIG. 4A

•Using the nuts and fl at washers removed from tractor back plate, install the bagger support tube to the back plate as shown. Tighten securely.

SUPPORT

TUBE

FLAT

WASHER

3/8 NUT

BOLT

02330

 

FIG. 4B

•Install the two upper support brackets through the back plate and to the chassis, using the 10 x 19 mm (3/8"x3/4") carriage bolts and locknuts supplied.Tighten securely.

•Assemble both support brackets to the outside of the baggger support tube using two each 3/8 x 63,5mm hex bolts13/32" I.D. fl at washers and 3/8 locknuts from parts bag. Tighten securely.

•Replace discharge chute into rear opening of tractor. Secure the chute with the two hook straps.

3/8 LOCK NUT

3/8 LOCK NUT

SUPPORT BRACKET

13/32 FLAT WASHER

3/8 HEX BOLT

3/8 CARRIAGE BOLT

02590

 

FIG. 4C

NOTE:The strap hook must go through the discharge chute only. Do not allow the hook to enter the slot in the tractor back plate.This will allow the discharge chute to float with the mower deck when moving on uneven terrain.

DISCHARGE

CHUTE

HOOK

02306

BACKPLATE

SLOT

FIG. 4D

TO ASSEMBLE BAGGER (See Figs. 5 & 6)

NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together.

•Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts.

•Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely.

FRONT BAGGER TUBE

LOWER

BAGGER

 

 

 

 

TUBE

1/4 X 2"

 

 

CARRIAGE

1/4 LOCK

 

BOLTS

2

0259

 

NUT

 

FIG. 5

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CTH180 XP Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsTo Assemble and Install Mulcher Plug See Fig Bagger Adjustment See FigHorizontal Adjustment Vertical AdjustmentCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade CareEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral ADJUSTMENTSee FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH180 XP HAUCT18H42C, Product no 17Electrical KEY Part Description 259 258 Chassis and Enclosures Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 532 17 Control Throttle Mower Lift 532 15 94-61 Washer Asm Inner Spring W/Plunger Mower Repair Parts Bagger Warranty Statement Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 18 99-50 Rev 4.03.04 TR/MH
Top Page Image Contents