Husqvarna 3120XP manual EC-declaration of conformity, Applies to Europe only, 0404/09/2119

Page 39

TECHNICAL DATA

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the chain saw for forest service Husqvarna 3120XP from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of May 17, 2006 "relating to machinery" 2006/42/EC.

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100:2010, ISO 14982:2009, EN ISO 11681-1:2011.

Notified body: 0404, SMP Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12, point 3b. The certificates for EC type examination in accordance with annex IX, have the numbers:

0404/09/2119.

In addition, SMP, Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, Sweden, has certified conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certificate has the number: 01/161/020.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna October 31, 2013

Per Gustafsson, Development manager

(Authorized representative for Husqvarna AB and responsible for technical documentation.)

English – 39

Image 39
Contents 3120XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerSharpening your chain and adjusting depth gauge setting Increased if the depth gauge setting is Adjustment of depth gauge settingToo large Chain oil Tensioning the chainLubricating cutting equipment Which could lead to serious, even fatalChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationBar Assembly Fitting the bar and chainWorking with the chain Fuel Fuel HandlingFuel safety FuellingExtra chain oil Long-term storage Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useWorking Techniques Limbing Basic cutting techniqueTerms There are five important factors you should considerTree felling technique Safe distanceFelling direction Your saw Clearing the trunk and preparing your retreatFelling cut Felling Training we advise you not to fell treesCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?Cutting the trunk into logs Carburettor MaintenanceHigh speed jet H Correctly adjusted carburettorImmediately Checking the brake triggerMuffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Changing a broken recoil springFitting the starter Must always be replaced Air filterSpark plug Lubricating the bar tip sprocketAdjustment of the oil pump Needle bearing lubricationCooling system Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Guide bar and saw chain combinations0404/09/2119 EC-declaration of conformityApplies to Europe only EN ISO 121002010, ISO 149822009, EN ISOOriginal instructions 1153183-26
Related manuals
Manual 40 pages 34.12 Kb