Husqvarna 288XP/XP lite manual Clearing the trunk and preparing your retreat, Felling

Page 22

SAFETY INSTRUCTIONS

C Clearing the trunk and preparing your retreat

Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees behind the intended felling direction.

D Felling

Felling is done using three cuts. First you make the DIRECTIONAL CUTS, which consist of the TOP CUT and the BOTTOM CUT; followed by the FELLING CUT. By placing these cuts correctly you can control the felling direction very accurately.

DIRECTIONAL CUT

To make the DIRECTIONAL CUT you begin with the TOP CUT. Stand to the right of the tree and cut downwards at an angle.

Next make the BOTTOM CUT so that it finishes at the end of the TOP CUT.

The directional cut should run 1/4 of the diameter through the trunk and the angle between the TOP CUT and BOTTOM CUT should be 45°.

The line where the two cuts meet is called the

DIRECTIONAL CUT LINE. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

FELLING CUT

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut with the bottom edge of the bar.

Make the FELLING CUT about 3-5 cm (1.5-2 inches) above the flat section of the

DIRECTIONAL CUT.

Use full throttle and bring the bar and chain slowly into the tree. Make sure the tree does not start to move in the opposite direction to your intended felling direction. Drive a WEDGE or BREA- KING BAR into the cut as soon as it is deep enough.

Finish the FELLING CUT parallel with the DIRECTIONAL CUT LINE so that the distance between them is at least at least 1/10 of the trunk diameter. The uncut section of the trunk is called the BREAKING STRIP.

The BREAKING STRIP act as hinges that control the felling direction of the falling tree.

All control over the felling direction is lost if the BREA- KING STRIP is too narrow or if the directional cut and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall under its own weight or with the aid of a FELLING WEDGE or BREAKING BAR.

22 – English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 288XP/XP Lite 101 90KEY to Symbols SymbolsContents Chain SAW Safety Equipment Safety InstructionsPersonal Protective Equipment Chain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Do not let go of the handles General rulesNever use the saw one- handed Min m General Safety Precautions10 ft Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling FuelmixMin 3 m Fuelling10ft Cold engine Start and StopStart Warm engineMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springSpark plug Adjusting the oil pumpAir filter MufflerTemperature -5oC 23oF or colder Needle bearing maintenance Winter useTemperature 0oC 32oF or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights Obligations1998W48

288XP/XP lite specifications

The Husqvarna 288XP and XP Lite chainsaws represent a pinnacle in forestry and tree care technology, designed for professionals who demand high performance and reliability in demanding environments. These models are renowned for their robust construction and impressive power-to-weight ratios, making them suitable for a variety of cutting tasks.

One of the standout features of the Husqvarna 288XP is its powerful engine. Equipped with a 75.6 cc two-stroke engine, it delivers a remarkable power output while maintaining efficiency. This ensures that the chainsaw can handle even the most challenging applications, from felling large trees to limbing and bucking with ease. The XP Lite version offers a slightly lighter design, making it more maneuverable while still delivering ample power for professional use.

The chainsaw also incorporates a high-performance air injection system. This unique technology helps to keep the air filter cleaner for longer periods by using centrifugal force to remove larger dust and debris particles before they reach the filter. As a result, users benefit from extended service intervals and less downtime for maintenance, which is crucial in professional settings.

Noise reduction is another important feature of the Husqvarna 288XP series. The saw is equipped with effective vibration damping, reducing fatigue during long operational hours. Additionally, it boasts advanced muffler technologies that help minimize noise levels, allowing operators to work in a variety of environments without disturbing the peace.

Ergonomics play a significant role in the design of these chainsaws. The adjustable chain oil flow ensures optimal lubrication, which improves cutting efficiency and prolongs the life of the chain and bar. The chainsaws also feature an ergonomic handle design, providing comfort and control during use, which is essential for precision cutting.

Safety is paramount in chainsaw design, and the Husqvarna 288XP includes several safety features, such as a chain brake, which activates in the event of kickback, protecting the operator from accidents. The tool-free chain tensioning system allows for quick adjustments on the job, further enhancing user safety and efficiency.

In summary, the Husqvarna 288XP and XP Lite chainsaws are engineered for the professional user who values performance, durability, and safety. With their powerful engines, innovative technologies, ergonomic designs, and commitment to user comfort and safety, these chainsaws are the ideal choice for those working in the most demanding forestry and tree care situations. Whether tackling large-scale projects or precision tasks, the Husqvarna 288XP series is built to meet and exceed expectations.
Top Page Image Contents