Husqvarna 288XP/XP lite manual Starter device, Changing a broken or worn starter cord

Page 30

MAINTENANCE

Starter device

!WARNING!

•When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries.

•Always be careful, when changing the recoil spring or the starter cord. Always wear safety goggles for eye protection.

Changing a broken or worn starter cord

• Loosen the screws, that hold the starter device against the crankcase and remove the starter device.

•Pull out the cord approx. 30 cm and lift it up into the notch in the pulley. Zero-set

the recoil spring by letting the pulley rotate slowly backwards. Undo the screw in the centre of the pulley and remove the pulley.

• Insert and fasten a new starter cord in the pulley. Wind approx. 3 turns of the starter cord on to the pulley. Assemble the starter pulley against the recoil spring, so the end of the spring engages to the pulley. Fit the screw in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Make a knot on the starter cord.

Tensioning the recoil spring

•Lift the starter cord up in the notch on the starter pulley and turn the starter pulley 2 turns clockwise.

NOTE! Check that the starter pulley can be turned at least half a turn, when the starter cord is entirely pulled out.

Changing the broken recoil spring

•Lift the starter pulley (see "Changing a broken or worn

starter cord").

•The recoil spring is disassembled from the

starter device, with its inside facing down. Tap the starter lightly against a working bench or similar. If the spring pops out when assembling, it should be mounted again, out and in towards the centre.

•Lubricate the recoil spring with thin oil. Assemble the

starter pulley, and tension the recoil spring.

Starter device assembly

•Assemble the starter device, by pulling the starter cord out first, then place the starter against the crankcase. Then slowly release the starter cord so

that the pulley engages with the pawls.

• Assemble and tighten the screws, which hold the starter.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 288XP/XP Lite 101 90KEY to Symbols SymbolsContents Safety Instructions Chain SAW Safety EquipmentPersonal Protective Equipment Chain brake and front hand guard Throttle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearance Setting the raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?General rules Do not let go of the handlesNever use the saw one- handed General Safety Precautions Min m10 ft Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling FuelmixFuelling Min 3 m10ft Cold engine Start and StopStart Warm engineMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springSpark plug Adjusting the oil pumpAir filter MufflerTemperature -5oC 23oF or colder Needle bearing maintenance Winter useTemperature 0oC 32oF or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights Obligations1998W48

288XP/XP lite specifications

The Husqvarna 288XP and XP Lite chainsaws represent a pinnacle in forestry and tree care technology, designed for professionals who demand high performance and reliability in demanding environments. These models are renowned for their robust construction and impressive power-to-weight ratios, making them suitable for a variety of cutting tasks.

One of the standout features of the Husqvarna 288XP is its powerful engine. Equipped with a 75.6 cc two-stroke engine, it delivers a remarkable power output while maintaining efficiency. This ensures that the chainsaw can handle even the most challenging applications, from felling large trees to limbing and bucking with ease. The XP Lite version offers a slightly lighter design, making it more maneuverable while still delivering ample power for professional use.

The chainsaw also incorporates a high-performance air injection system. This unique technology helps to keep the air filter cleaner for longer periods by using centrifugal force to remove larger dust and debris particles before they reach the filter. As a result, users benefit from extended service intervals and less downtime for maintenance, which is crucial in professional settings.

Noise reduction is another important feature of the Husqvarna 288XP series. The saw is equipped with effective vibration damping, reducing fatigue during long operational hours. Additionally, it boasts advanced muffler technologies that help minimize noise levels, allowing operators to work in a variety of environments without disturbing the peace.

Ergonomics play a significant role in the design of these chainsaws. The adjustable chain oil flow ensures optimal lubrication, which improves cutting efficiency and prolongs the life of the chain and bar. The chainsaws also feature an ergonomic handle design, providing comfort and control during use, which is essential for precision cutting.

Safety is paramount in chainsaw design, and the Husqvarna 288XP includes several safety features, such as a chain brake, which activates in the event of kickback, protecting the operator from accidents. The tool-free chain tensioning system allows for quick adjustments on the job, further enhancing user safety and efficiency.

In summary, the Husqvarna 288XP and XP Lite chainsaws are engineered for the professional user who values performance, durability, and safety. With their powerful engines, innovative technologies, ergonomic designs, and commitment to user comfort and safety, these chainsaws are the ideal choice for those working in the most demanding forestry and tree care situations. Whether tackling large-scale projects or precision tasks, the Husqvarna 288XP series is built to meet and exceed expectations.
Top Page Image Contents