Husqvarna 175 AWD manual Storage, Winter storage, Guard, Service

Page 33

Storage

Winter storage

At the end of the season, or if the machine is going to stand idle for more than 30 days, it should immediately be made ready for storage. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. If alkylate petrol (Aspen) is used stabiliser is not necessary since this fuel is stable. However, one should avoid changing from standard to alkylate petrol since sensitive rubber parts can harden. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

WARNING! Never place an engine with fuel

!in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, drying cabinets, etc. Exercise caution when handling fuel. It is highly inflammable, and careless use can cause serious injury and damage to property. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degreasing agents and hot water instead.

To prepare the machine for storage follow these instructions:

1Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3Change the engine oil, and take care of the waste oil.

4Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5Remove the plugs and pour about a tablespoon of engine oil into each cylinder. Pull round the engine to distribute the oil and screw the plugs back on.

6Grease all grease nipples, joints and axles.

7Remove the battery. Clean it, charge it, and store it in a cool place.

8Store the machine in a clean and dry place and cover it over for extra protection.

Guard

There is a cover to protect your machine during storage or transport. Contact your dealer for a demonstration

Service

Low season is the most suitable time to perform a service or overhaul of the machine in order to ensure high function safety during high season.

When ordering spare parts state your machine’s purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or tuning by an authorised service workshop is a good way of getting the best out of your machine the next season.

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Rider 175 Rider 175 AWD Contents Service journal Pre-delivery serviceAfter the first 8 hours Dear Customer IntroductionDriving and transport on public roads TowingSerial Number Good serviceSymbols KEY to SymbolsKEY to Symbols Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Exercise care and refuel outdoors see safety instructions Cutting height adjustment leverSeat FuellingDriving Before startingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineOther objects which can be thrown out by the blades Release lever Release lever Rider 175 AWDRelease lever Rider Maintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 175 AWD Adjusting the parking brake RiderChecking and adjusting of throttle wire Can result in reduced braking abilityReplacement of fuel filter Replacing the air filterCool before starting to replace the air filter Checking the fuel pump’s air filter Check the level of the battery acidIgnition system Replacing the spark plugCheck the safety system Main fuse When the engine is running. Mind your fingersChecking the tyre pressure Checking the engine’s cooling air intakeTrapping your hand Removing the cutting unitAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Placing in the service position Service position for the cutting unitRestoring from service position Checking the bladesRemoving the BioClip plug Checking the engine’s oil level LubricationChanging the oil filter Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only 1150315-26 ´z+R?T¶6&¨ ´z+R?T¶6&¨
Related manuals
Manual 40 pages 6.96 Kb

175, 175 AWD specifications

The Husqvarna 175 AWD is a powerful and versatile snow blower designed for residential and commercial use. Known for its reliability and performance, this machine excels in various snow conditions, making it an essential tool for winter maintenance.

One of the standout features of the 175 AWD is its all-wheel drive system. This technology provides superior traction and stability, ensuring that the snow blower can maneuver easily over uneven terrain and through deep snow. The AWD feature gives users peace of mind, knowing they can tackle challenging winter weather with confidence.

Equipped with a robust engine, the 175 AWD delivers impressive power. Its efficient engine design allows for superior throw distance, enabling users to clear large areas quickly. The snow blower’s 24-inch clearing width makes it particularly effective for broader driveways and walkways, significantly reducing the time spent on snow removal.

The 175 AWD also features an adjustable auger and chute, providing users with the flexibility to direct snow where it is needed. The auger is designed to handle heavy, packed snow as well as light, fluffy snow, making it adaptable to various snow conditions. The ability to modify the chute’s angle and direction ensures optimal performance in any scenario.

User comfort is another crucial aspect of the Husqvarna 175 AWD. It comes with heated hand grips that keep operators warm during cold winter days, allowing for extended use without discomfort. The ergonomic design and intuitive controls make it easy for users to operate the machine efficiently, even in challenging conditions.

Additionally, the snow blower features an easy-to-start ignition system, ensuring that it fires up promptly even in frigid temperatures. The durable construction of the 175 AWD is built to withstand the rigors of winter, offering longevity and reliable service for years to come.

In summary, the Husqvarna 175 AWD snow blower combines power, technology, and user-focused design. Its all-wheel drive system, adjustable features, and comfort enhancements make it a strong contender in the snow removal market. Whether for home or commercial use, the 175 AWD is designed to make snow clearing more manageable and efficient, ensuring that winter doesn’t slow you down. This machine stands out as a trusted companion in the fight against snow and ice, ready to take on the toughest winter challenges.
Top Page Image Contents