Husqvarna 175 AWD manual Lubrication, Checking the engine’s oil level, Replacing the engine oil

Page 33

Lubrication

Checking the engine’s oil level.

Check the oil level in the engine when the Rider stands horizontal with the engine switched off.

Open the engine cover.

Loosen the dipstick, pull it up and wipe it off.

Now insert the dipstick again. The dipstick should be completely screwed down

Pull the dipstick out again and read the oil level.

The oil level should be between the markings on the dipstick. If the level is approaching the ADD mark, top up the oil to the FULL mark on the dipstick.

ADD FULL

ADD FULL

The oil is topped up through the hole the dipstick sits in. Fill the oil slowly.

Tighten the dipstick correctly before starting the engine. Start and run the engine at idling speed for approx. 30 seconds. Turn off the engine. Wait 30 seconds and check the oil level. If necessary fill so that the oil comes up to the FULL mark on the dipstick.

First and foremost use synthetic engine oil class SJ-CF 5W/ 30 or 10W/30 for all temperature ranges. Mineral oil SAE30, class SF–CC can be used at temperatures > +5 °C (40 °F)

Do not mix different types of oil.

Caution when using oils such as 5W-20, 10W-30 and 10W-40 the engine’s oil consumption increases. If these oils must be used, check the oil level frequently.

Replacing the engine oil

The engine oil should be changed the first time after 5 hours running time. It should then be changed after every 50 hours of running time. When operating with a heavy load or at high ambient temperatures, replace every 25 hours.

WARNING! Engine oil can be very hot if it is

!drained directly after stopping the engine. Allow the engine to cool somewhat first.

1 Place a container underneath the engine’s left oil drain plug.

2Remove the dipstick. Remove the drain plug from the engine’s left side.

3Let the oil run out into the container.

4 Fit the drain plug and tighten it.

5If necessary fill so that the oil comes up to the FULL mark on the dipstick. The oil is topped up through the hole the dipstick sits in. See Checking the engine’s oil level for filling instructions. The engine holds 1.4 litres (1.5 USqt) when the oil filter is not replaced and 1.6 litres (1.7 USqt) of oil when the oil filter is replaced.

6Run the engine warm, then check that there is no leakage from the oil plug.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Rider 175 Rider 175 AWD Contents Service journal Pre-delivery serviceAfter the first 8 hours Dear Customer IntroductionDriving and transport on public roads TowingSerial Number Good serviceSymbols KEY to SymbolsKEY to Symbols Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Exercise care and refuel outdoors see safety instructions Cutting height adjustment leverLifting lever for the cutting unit SeatRelease lever Release lever RiderRelease lever Rider 175 AWD Driving Before startingStart the engine Starting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving the Rider Cutting tipsOther objects which can be thrown out by the blades Stop the engine Maintenance schedule MaintenanceRemoving of the machine hoods CleaningAdjusting the parking brake Rider Checking and adjusting the steering wiresAdjusting the parking brake Rider 175 AWD Can result in reduced braking abilityReplacement of fuel filter Checking and adjusting of throttle wireCool before starting to replace the air filter Replacing the air filterChecking the fuel pump’s air filter Controlling the acid level in a dry- charged batteryIgnition system Replacing the spark plugCheck the safety system Main fuse When the engine is running. Mind your fingersChecking the tyre pressure Checking the engine’s cooling air intakeTrapping your hand Adjusting the parallelism of the cutting unit Removing the cutting unitChecking the cutting unit’s parallelism Service position for the cutting unit Placing in the service positionReplacing the cutting unit belts Restoring from service position Removing the BioClip plug Checking the bladesLubrication Checking the engine’s oil levelReplacing the engine oil Changing the oil filter Lubricating the belt adjusterChecking the transmission oil level General lubricationProblem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only Page 1150315-26 ´z+R?T¶6&¨ ´z+R?T¶6&¨
Related manuals
Manual 36 pages 27.85 Kb

175, 175 AWD specifications

The Husqvarna 175 AWD is a powerful and versatile snow blower designed for residential and commercial use. Known for its reliability and performance, this machine excels in various snow conditions, making it an essential tool for winter maintenance.

One of the standout features of the 175 AWD is its all-wheel drive system. This technology provides superior traction and stability, ensuring that the snow blower can maneuver easily over uneven terrain and through deep snow. The AWD feature gives users peace of mind, knowing they can tackle challenging winter weather with confidence.

Equipped with a robust engine, the 175 AWD delivers impressive power. Its efficient engine design allows for superior throw distance, enabling users to clear large areas quickly. The snow blower’s 24-inch clearing width makes it particularly effective for broader driveways and walkways, significantly reducing the time spent on snow removal.

The 175 AWD also features an adjustable auger and chute, providing users with the flexibility to direct snow where it is needed. The auger is designed to handle heavy, packed snow as well as light, fluffy snow, making it adaptable to various snow conditions. The ability to modify the chute’s angle and direction ensures optimal performance in any scenario.

User comfort is another crucial aspect of the Husqvarna 175 AWD. It comes with heated hand grips that keep operators warm during cold winter days, allowing for extended use without discomfort. The ergonomic design and intuitive controls make it easy for users to operate the machine efficiently, even in challenging conditions.

Additionally, the snow blower features an easy-to-start ignition system, ensuring that it fires up promptly even in frigid temperatures. The durable construction of the 175 AWD is built to withstand the rigors of winter, offering longevity and reliable service for years to come.

In summary, the Husqvarna 175 AWD snow blower combines power, technology, and user-focused design. Its all-wheel drive system, adjustable features, and comfort enhancements make it a strong contender in the snow removal market. Whether for home or commercial use, the 175 AWD is designed to make snow clearing more manageable and efficient, ensuring that winter doesn’t slow you down. This machine stands out as a trusted companion in the fight against snow and ice, ready to take on the toughest winter challenges.
Top Page Image Contents