Husqvarna 1153163-95 manual Maintenance schedule

Page 38

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

Daily maintenance

Weekly maintenance

Monthly maintenance

 

 

 

 

On chain saws without a catalytic

Check the brake band on the chain

 

brake for wear. Replace when less

Clean the outside of the machine.

converter, check the cooling system

than 0.024 inch (0.6 mm) remains at

 

weekly.

 

the most worn point.

 

 

 

 

 

Check that the components of the

Check the starter, starter cord and

Check the clutch centre, clutch drum

throttle control work safely. (Throttle

return spring.

and clutch spring for wear.

lockout and throttle control.)

 

 

 

 

 

Clean the chain brake and check that

 

 

it operates safely. Make sure that the

Check that the vibration damping

Clean the spark plug. Check that the

chain catcher is undamaged, and

elements are not damaged.

electrode gap is 0.020 inch (0.5 mm).

replace it if necessary.

 

 

 

 

 

The bar should be turned daily for

 

 

more even wear. Check the

 

 

lubrication hole in the bar, to be sure it

Lubricate the clutch drum bearing.

Clean the outside of the carburetor.

is not clogged. Clean the bar groove.

 

 

If the bar has a sprocket tip, this

 

 

should be lubricated.

 

 

 

 

 

Check that the bar and chain are

File off any burrs from the edges of

Check fuel hose for cracks or other

getting sufficient oil.

the bar.

damage. Change if necessary.

 

 

 

Check the saw chain with regard to

 

 

visible cracks in the rivets and links,

 

 

whether the saw chain is stiff or

Clean or replace the spark arrestor

Empty the fuel tank and clean the

whether the rivets and links are

screen on the muffler.

inside.

abnormally worn. Replace if

 

 

necessary.

 

 

 

 

 

Sharpen the chain and check its

 

 

tension and condition. Check the drive

Clean the carburetor compartment.

Empty the oil tank and clean the

sprocket for excessive wear and

inside.

 

replace if necessary.

 

 

 

 

 

Clean the starter units air intake.

Clean the air filter. Replace if

Check all cables and connections.

necessary.

 

 

 

 

 

Check that nuts and screws are tight.

 

 

 

 

 

Check that the stop switch works

 

 

correctly.

 

 

 

 

 

Check that there are no fuel leaks

 

 

from the engine, tank or fuel lines.

 

 

 

 

 

On chain saws with a catalytic

 

 

converter, check the cooling system

 

 

daily.

 

 

 

 

 

38 – English

Image 38
Contents 346XP, 346XPG, 346XP Tech 353, 353G EnglishSymbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Needle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before Clutch cover causing the chain toCleaning Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWhen making adjustments Air Injection centrifugal cleaningTemperature 0C 32F or colder Cooling system346XPG, 353G Heated handlesElectrical carburetor heating Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataRecommended cutting equipment for Canada Bar and chain combinationsSaw chain filing and file gauges 050Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage Original instructions 1153163-95