Husqvarna 1150902-95 manual Cutting equipment designed to reduce kickback, Bar, Chain

Page 12

GENERAL SAFETY PRECAUTIONS

recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or

! the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating

! saw chain can cause extremely serious injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

Length (inches/cm)

Number of teeth on bar tip sprocket (T).

Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

Chain pitch (inches)

12 – English

Image 12
Contents 455e Rancher Rancher 460 Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Stop switch Cutting equipmentVibration damping system MufflerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment 455e RancherFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Bar Assembly Fitting the bar and chainRancher, 460 Rancher 455e RancherAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lockout Muffler StarterChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderTemperature -5C 23F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Repair or Replacement of Parts Repair orConsequential Damages Husqvarna Forest American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1150902-95