Husqvarna 1150902-95 Air Injection centrifugal cleaning, Winter use, Temperature 0C 32F or colder

Page 38

MAINTENANCE

5 Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburetor passes through the starter. Dirt and dust is pushed out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained. Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburetor compartment.

Winter use

Running problems can occur when using the machine in the cold and snowy conditions caused by:

Too low engine temperature.

Icing of the air filter and carburetor. Special measures are therefore often required:

Partly mask the air inlet on the starter to increase the working temperature of the engine.

Temperature 0°C (32°F) or colder:

The cylinder cover is designed so it can be adjusted for running in cold weather, so that preheated air from the cylinder can pass into the carburetor space preventing icing of the air filter, etc.

Temperature -5°C (23°F) or colder:

For running the machine in cold weather or powder snow, a special cover is available, which is mounted on the starter housing. This reduces the intake of cold air and prevents large amounts of snow from being sucked in.

CAUTION! If the special winterising kit has been fitted or any measures have been taken to increase the temperature these changes must be reversed before the machine is used in normal temperature conditions. Otherwise there is a risk of overheating, resulting in severe damage to the engine.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

38 – English

Image 38
Contents 455e Rancher Rancher 460 Rancher Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping system Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipment455e Rancher Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Bar Rancher, 460 Rancher AssemblyFitting the bar and chain 455e RancherAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the front hand guard Correctly adjusted carburetorChecking brake band wear Checking the inertia brake releaseThrottle lockout Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationTemperature -5C 23F or colder Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesConsequential Damages Husqvarna Forest Federal Emission Control Warranty StatementRepair or Replacement of Parts Repair or Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1150902-95