Husqvarna 115 13 81-95 manual Stopping

Page 22

STARTING AND STOPPING

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use.

WARNING! Long term inhalation of the

! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk.

• Never start a chain saw unless the bar, chain and all covers are ﬁtted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury.

•The chain brake should be activated when starting. Se instructions under the heading Start and stop. Do not drop start. This method is very dangerous because you may lose control of the saw.

•Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.

•Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment.

•Always hold the saw with both hands. The right hand should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a ﬁrm grip with thumbs and ﬁngers encircling the chain saw handles.

Stopping

Stop the engine by pushing the start/stop switch down.

CAUTION! The start/stop switch automatically returns to run position. To avoid involuntary start up, the spark plug cap must always be removed from the spark plug when the machine is unsupervised.

22 – English

115 13 81-95 Rev.3 2008-12-15

Image 22

Contents 445 445e 450e Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will ﬁnd the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufﬂerBar General rulesCutting equipment designed to reduce kickback ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain 445 445e, 450eFilling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment 445 AssemblyFitting the bar and chain 445e, 450eAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Cold engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking the inertia brake release Mufﬂer Replacing the starter cord StarterTensioning the recoil spring Fitting the starter Air ﬁlterReplacing the return and drive springs Recoil spring aNeedle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain ﬁling and ﬁle gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151381-95