Husqvarna 1153183-26 manual Cutting equipment, Stop switch, Muffler, General rules

Page 10

GENERAL SAFETY PRECAUTIONS

Stop switch

Use the stop switch to switch off the engine.

Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

! engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

In areas with a hot, dry climate there is a high risk of fires. These areas are sometimes subject to government rules requiring among other things the muffler must be equipped with an approved type of spark arrestor mesh.

CAUTION! The muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/or vapours.

WARNING! Never use a saw without a

! muffler, or with a damaged muffler. A damaged muffler may substantially increase the noise level and the fire hazard. Keep fire fighting equipment handy. If a spark arrestor screen is required in your area, never use the saw without or with a broken spark arrestor screen.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of kickback.

•Reduce the risk of the saw chain breaking or jumping off the bar.

•Obtain optimal cutting performance.

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

•Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or

! the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

10 – English

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 3120XP Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Sharpening your chain and adjusting depth gauge settingBar General information on sharpening cutting teethAdjustment of depth gauge setting Increased if the depth gauge setting isToo large Cause serious or even fatal injury Tensioning the chainLubricating cutting equipment Filling with chain oilNeedle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelFuelling Fuel safetyExtra chain oil Transport and storage Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsWorking Techniques Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Felling cut Clearing the trunk and preparing your retreatDirectional cuts Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Maintenance CarburettorCorrectly adjusted carburettor High speed jet HChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Changing a broken recoil spring Tensioning the recoil springFitting the starter Spark plug Air filterLubricating the bar tip sprocket Needle bearing lubrication Adjustment of the oil pumpRunning when making adjustments Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEN ISO 12100-22003, Cispr 122005, EN ISO EC-declaration of conformityApplies to Europe only 0404/09/2119Page Page Page Page Original instructions 1153183-26
Top Page Image Contents