Husqvarna 130BT, 115 31 90-95 manual Operation, Control ARM 350BF/370BFS/380BFS, Starting Engine

Page 17

Operation

CONTROL ARM [350BF/370BFS/380BFS]

-Hold the upper end of the control arm in hand and, while pulling it away from the unit, rotate arm forward (counter-clockwise in the direction of the arrow) until it clicks. (The first position)

And if you want, you can rotate arm further until it clicks. (The second position)

Choose the arm position according to your working condition.

-To fold the arm, reverse the order.

(1)First position (2)Second position

STARTING ENGINE

IMPORTANT

-Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating.

1.Push the primer bulb until fuel flows out in the clear tube.

2.When the engine is cool, close the choke.

(1)Choke Lever (2)Primer Bulb (3)OPEN (4)CLOSE

3.Set the throttle lever position.

[130BT][350BT/BF] [370BTS/BFS] [380BTS/BFS] IdlingAbout 1/3 Open

(1)Full Throttle (2)About 1/3 Open (3)Idling

(4)STOP [130BT/350BT/370BTS/380BTS] as shown in F19 (5)Stop Switch [350BF/370BFS/380BFS] as shown in F20

4.To start, hold the top of the blower firmly with your left hand. Pull the starter knob slowly until you feel it engage and then give it a vigorous strong pull.

IMPORTANT

-Never twist the starter cord around your hand.

-Avoid pulling the starter rope out to its full extent and allowing the starter rope to snap back. This will prevent premature damage to the starter.

-Do not let a person stand near the blower or the exhaust port.

5.Once the engine is running, gradually open the choke if it was set closed, and let the engine run at idle speed for a minute to warm it up.

NOTE

When the engine fails to start after several attempts due to overchoking, open the choke and repeat pulling the rope.

WARNING

Air comes out as soon as the engine is started, even at idle speed.

 

English

F14

 

[350BF] [370BFS] [380BFS]

F15

 

(1)

 

(2)

 

[350BF] [370BFS] [380BFS]

F16

(1)

 

 

(4)

 

(3)

(2)

[130BT]

F17

(1)

 

 

(3)

 

(4)

(2)

[350BT/BF]

F18

(1)

 

 

(3)

 

(4)

(2)

 

[370BTS/BFS] [380BTS/BFS]

F19

(2)

 

(3)

(4)

(1)

 

[130BT/350BT/370BTS/380BTS]

F20

(5)

(1)

 

(2)

 

 

 

 

(3)

 

[350BF] [370BFS] [380BFS]

F21

 

 

17

Image 17
Contents Applicable Serial Numbers 00100101 and up 130BT 350BT/BF 370BTS/BFS 380BTS/BFS EnglishWhat is not Covered Your Warranty Rights and ObligationsOWNER’S Warranty Responsibilities Warranty COMMENCE- Ment DateContents Symbols SafetySafety First Safety Precautions Symbols on the machineWorking Conditions ModelWorking Circumstance Avoid Noise ProblemWorking Plan Fuel130BT 350BT/BF 370BT/BF 380BT/BF Using the ProductBefore Starting the Engine Storage MaintenanceTransportation Disposal What is what?130BT 350BT 350BF 350BT/BF370BTS 370BFS 370BTS/BFS380BTS 380BFS 380BTS/BFSModel Technical dataFlexible Hose and Swivel Joint AssemblyRight Handle 350BF/370BFS/380BFS Handlebar Option 130BT/350BT/370BTSHarness Blow PipesWaist Belt 350BT/BF 370BTS/BFS 380BTS/BFS 130BT has no waist beltFuel HOW to MIX FuelFuel Fueling the UnitStarting Engine OperationControl ARM 350BF/370BFS/380BFS Stopping Engine Adjusting Idle SpeedCleaning AIR Filter 130BT F29 MaintenanceAIR Cleaner Spark Plug Fuel FilterMuffler Spark ArresterCooling System StorageAIR Inlet NET Sholder Strap