Husqvarna 170BT, 170BF manual Symbols on the machine, Safety Precautions, Position Intake CUP

Page 5

English

Symbols on the machine

(a)

(b)

(c)

(d)

 

 

 

 

 

 

 

 

For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake.

(a) The port to refuel the "MIX GASOLINE"

(c) The direction to open the choke

Position: FUEL TANK CAP

Position: INTAKE CUP

(b) The direction to close the choke

(d) The direction to stop the engine

Position: INTAKE CUP

Position: THROTTLE LEVER [130 BT/170 BT only]

<FOR EPA ONLY>

<FOR EPA & CARB>

A

A

B

B

C

C

1 : THE ACTUAL MANUFACTURING MONTH WILL BE PRINTED.

A : Model

B : ENGINE FAMILY

C : ENGINE DISPLACEMENT

 

 

 

130BT

7KZXS.0294BK 2

29cc

170BT/170BF

7KZXS.0655BE 2

65cc

2 : THE INITIAL NUMBER WILL BE CHANGED EVERY YEAR OF MANUFACTURING.

This engine label certifies that the product is certified in accordance with American exhaust emissions requirements EPA Ph II and CARB Tier III. The Emissions Compliance Period

referred to on the emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal and California emission requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

For customer assistance call: 704-921-7000 or contact us at our

website: www.husqvarna.com

IMPORTANT

Check the emission information label on your product. In the case of <FOR EPA ONLY>, the product is unsupported to use in California.

Safety Precautions

WARNING

1.Read this Blower Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury.

2.Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. Also note that you are requested to contact the dealer from whom you purchased the product for assistance the event that you have any questions which cannot be answered herein.

3.Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

4.Do not lend or rent your machine without the owner's manul.

5.Be sure that anyone using your unit understands the information contained in this manual.

6.Never let a child use the machine.

7.Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

8.Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others.

9.A blower is a dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator’s manual.

10.Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.

11.The machine is only designed for blowing lawns, pathways, asphalt roads and the like.

5

Image 5
Contents 130BT 170BT MANUFACTURER’S Warranty Coverage Your Warranty Rights and ObligationsOWNER’S Warranty RESPONSI- Bilities Warranty Commencement DateContents Safety First SafetySafety Precautions Symbols on the machinePosition Intake CUP For EPA only For EPA & CarbWorking Conditions Avoid Noise ProblemWorking Circumstance Working PlanBefore Starting the Engine Using the ProductStorage MaintenanceTransportation „ Disposal What is what?170BT 170BF 170BT/170BF130BT 170BT 170BF Technical dataModel Assembly 130BT has no waist belt „ Blower Tubes„ Harness Fuel „ HOW to MIX Fuel„ Fuel „ Fueling the Unit„ Control ARM 170BF Operation„ Starting Engine Close1Idling Adjustment Screw 170BT/170BF „ Adjusting Idle SpeedIdling Adjustment Screw „ Stopping EngineCleaning AIR Filter Maintenance„ AIR Cleaner „ Spark Plug „ Fuel Filter„ Muffler „ Spark Arrester„ AIR Inlet NET Storage„ Ignition Coil AIR GAP Inspection „ Sholder Strap