Husqvarna 1153183-95 manual Fuel Handling, Gasoline, Two-stroke oil, Mixing

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

 

 

Gasoline

•Use good quality unleaded gasoline.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures.

•Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,43/0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 3120XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesBar Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback ChainIncreased if the depth gauge setting is Too largeLubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Bar and cause serious or even fatal injuryChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Gasoline Fuel HandlingFuel Two-stroke oilFueling Chain oilExtra chain oil Fuel safety Transport and storageLong-term storage Cold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsWorking Techniques Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreat Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance CarburetorCorrectly adjusted carburetor High speed jet HChecking the brake trigger ImmediatelyMuffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Changing a broken recoil springFitting the starter Lubricating the bar tip sprocket Air filterSpark plug Must always be replacedNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage Original instructions 1153183-95

1153183-95 specifications

The Husqvarna 1153183-95 is an innovative product from Husqvarna, well-known for delivering high-quality outdoor power equipment. This model is specifically designed to cater to the needs of both amateur gardeners and professional landscapers. Its advanced features and technologies make it a standout choice in the market.

One of the primary features of the Husqvarna 1153183-95 is its durability. Constructed with robust materials, the equipment is built to withstand the rigors of frequent use, ensuring longevity and reliability. The design is not only sturdy but also lightweight, allowing for easier maneuverability.

The 1153183-95 incorporates a powerful engine that delivers superior performance. This engine is engineered for optimum fuel efficiency, ensuring that users can complete their tasks without the worry of frequent refueling. Additionally, the low-emission technology in the engine contributes to a reduced environmental impact, aligning with modern sustainability goals.

An important aspect of the Husqvarna 1153183-95 is its user-friendly controls. The design includes ergonomic handles that provide comfort during extended use. These features reduce fatigue, allowing users to work longer and more efficiently. The intuitive control layout ensures that even novice users can operate the device without difficulty.

Another noteworthy technology included in the 1153183-95 is its cutting system. With precision blades, the equipment ensures clean and effective cutting, making it ideal for various landscaping tasks. The adjustable settings allow users to customize the cutting height, providing versatility based on the specific requirements of a project.

Moreover, this model features an advanced air filtration system. This system not only prolongs engine life but also enhances its performance by ensuring a clean air supply to the engine. This technology reduces maintenance needs and contributes to a smooth operation.

In summary, the Husqvarna 1153183-95 is a powerful and efficient outdoor equipment option, distinguished by its robust construction, user-friendly features, and innovative technologies. It is designed to meet the demands of both casual users and professionals, providing reliability and performance for a myriad of landscaping tasks. Whether you are maintaining a garden or managing a larger landscape, this model efficiently combines power, efficiency, and ease of use, making it a valuable addition to any outdoor toolkit.
Top Page Image Contents