Husqvarna 1153183-95 Clearing the trunk and preparing your retreat, Directional cuts, Felling cut

Page 27

WORKING TECHNIQUES

•Look for signs of damage and rot in the stem, this makes it more probably that the tree will break and start to fall before you expect it to.

You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended.

Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling.

The main point to avoid is letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly.

IMPORTANT! During critical felling operations, hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard.

Clearing the trunk and preparing your retreat

Delimb the stem up to shoulder height. It is safer to work from the top down and to have the tree between you and the saw.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling direction.

1 3

Felling

WARNING! Unless you have special

! training we advise you not to fell trees with a diameter larger than the bar length of your saw!

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cut you begin with the top cut. Aim using to the saw’s felling direction mark (1) toward a goal further forward in the terrain, where you would like the tree to fall (2). Stand on the right-hand side of the tree, behind the saw, and cut with a pull stroke.

Next make the bottom cut so that it finishes exactly at the end of the top cut.

1

2

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Felling cut

2

1

1

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

2

1Danger zone

2 Retreat path

3 Felling direction

Make the felling cut about 1.5-2 inches (3-5 cm) above the bottom directional cut.

English – 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 3120XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerChain Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback BarToo large Increased if the depth gauge setting isBar and cause serious or even fatal injury Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipmentNeedle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Two-stroke oil Fuel HandlingFuel GasolineFueling Chain oilExtra chain oil Fuel safety Transport and storageLong-term storage Warm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useWorking Techniques Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreat Directional cutsFelling cut Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?Cutting the trunk into logs Carburetor MaintenanceHigh speed jet H Correctly adjusted carburetorImmediately Checking the brake triggerMuffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Changing a broken recoil springFitting the starter Must always be replaced Air filterSpark plug Lubricating the bar tip sprocketCooling system Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementEmission Controlwarranty Parts List Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage Original instructions 1153183-95

1153183-95 specifications

The Husqvarna 1153183-95 is an innovative product from Husqvarna, well-known for delivering high-quality outdoor power equipment. This model is specifically designed to cater to the needs of both amateur gardeners and professional landscapers. Its advanced features and technologies make it a standout choice in the market.

One of the primary features of the Husqvarna 1153183-95 is its durability. Constructed with robust materials, the equipment is built to withstand the rigors of frequent use, ensuring longevity and reliability. The design is not only sturdy but also lightweight, allowing for easier maneuverability.

The 1153183-95 incorporates a powerful engine that delivers superior performance. This engine is engineered for optimum fuel efficiency, ensuring that users can complete their tasks without the worry of frequent refueling. Additionally, the low-emission technology in the engine contributes to a reduced environmental impact, aligning with modern sustainability goals.

An important aspect of the Husqvarna 1153183-95 is its user-friendly controls. The design includes ergonomic handles that provide comfort during extended use. These features reduce fatigue, allowing users to work longer and more efficiently. The intuitive control layout ensures that even novice users can operate the device without difficulty.

Another noteworthy technology included in the 1153183-95 is its cutting system. With precision blades, the equipment ensures clean and effective cutting, making it ideal for various landscaping tasks. The adjustable settings allow users to customize the cutting height, providing versatility based on the specific requirements of a project.

Moreover, this model features an advanced air filtration system. This system not only prolongs engine life but also enhances its performance by ensuring a clean air supply to the engine. This technology reduces maintenance needs and contributes to a smooth operation.

In summary, the Husqvarna 1153183-95 is a powerful and efficient outdoor equipment option, distinguished by its robust construction, user-friendly features, and innovative technologies. It is designed to meet the demands of both casual users and professionals, providing reliability and performance for a myriad of landscaping tasks. Whether you are maintaining a garden or managing a larger landscape, this model efficiently combines power, efficiency, and ease of use, making it a valuable addition to any outdoor toolkit.
Top Page Image Contents