Husqvarna 966609201 manual Fitting a blade guard, grass blade and grass cutter

Page 12

ASSEMBLY

Fitting a blade guard, grass blade and grass cutter

G

F

E

D

A

B

C

•Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt.

CAUTION! Use the recommended blade guard. See the Technical data section.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D), support cup (E) and support flange

(F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

Fitting a trimmer guard and Superauto II 1” trimmer head

 

 

K

K

G

 

F

B

 

I

J

I

C

 

 

 

 

A

•Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows:

Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half

(K). Pull apart the trimmer head, grasping the cover firmly.

•Place the cover (I) and the support flange (F) on the output shaft.

•Fit the nut (G). Tighten the nut to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Grasp the handle of the spanner as close to the trimmer guard as possible.

•To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

•Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

•To dismantle, follow the instructions in the reverse order.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 223R KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what on the clearing saw?General Safety Precautions Personal protective equipmentMachine′s safety equipment Stop switchThrottle lockout Cutting attachment guard Vibration damping systemQuick release MufflerCutting equipment Locking nutCutting equipment Sharpening grass cutters and grass bladesTrimmer head Assembly Fitting the handlebarFitting blades and trimmer heads Fitting a blade guard, grass blade and grass cutter Fitting a trimmer guard and Superauto II 1 trimmer headAdjusting the harness and clearing saw Fitting other guards and cutting attachmentsStandard harness Fuel safety Fuel HandlingFuel Fuelling MixingStarting and Stopping Check before startingStarting and stopping StartingStopping Basic safety rules Working TechniquesGeneral working instructions Basic working techniquesGrass clearing using a grass blade Grass trimming with a trimmer headMaintenance CarburettorFine adjustment of the idle speed T Correctly adjusted carburettorAdjusting the start throttle speed High speed jet HMuffler Cooling systemBevel gear Cleaning the air filter Air filterDrive shaft Spark plugMaintenance schedule MaintenanceTechnical Data Technical dataEC-declaration of conformity Applies to Europe onlySuper Auto Page T35 ´z+R9@¶6¨ S35 1150253-26 ´z+R9@¶6¨ ´z+R9@¶6¨
Top Page Image Contents