Image IMSB63120, IMSG63120, IMSG63120, IMSB63120 user manual Troubleshooting

Page 16

Troubleshooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-877-897-7493, Monday through Friday, 8 a.m. until 5 p.m. Central Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter from the filter housing and clean or replace the filter (see page 13).

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS, BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

indoors and the room temperature is main- tained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set tempera- ture.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature

Heating Time

70°F +

6 to 8 hours

50°F - 70°F

9 to 11 hours

30°F - 50°F

12 to 14 hours

b. If the water still has not heated after 24 hours, contact our customer service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.This usually occurs only when the water level is low. Add water until it is 2”–4” above the skim- mer basket.

b.The filter cover may not be tight. Make sure the filter cover is tight.

c.The skimmer basket may not be seated proper- ly. The top of the basket must be flush with the bottom of the weir door.

6. SYMPTOM: THE WATER DOES NOT HEAT

9. SYMPTOM: THE WATER LEVEL DROPS

a. Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. The water will heat at a rate of 6°F per hour. If you are using the spa

a. Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, the spa shell may have a leak. Contact your local pool and spa service provider for repairs.

16

Image 16
Contents Model No. IMSB63120 IMSG63120 Serial No Customer HOT LineTable of Contents Posting the Warning SignImportant Safety Instructions Read and Follow ALL InstructionsPage Page Before You Begin If you set up the hydrotherapy spa outside If you set up the hydrotherapy spa insideChoosing a Location for the Hydrotherapy Spa Assembly Be careful not to damage the spa shellPage Using the Hydrotherapy Spa Wiring the Hydrotherapy SPATesting and Treating the Water Starting the Hydrotherapy SPASpa Shell Diagram Using the Controls Maintenance Attaching and Removing Access Panels Water ChemistryMaintaining the Proper PH Balance Changing the Filter CycleDraining the Pumps Replacing the Light BulbTroubleshooting Symptom the Console Displays the Words Cool or ICE Symptom the Console Displays ONEPart List-Model No. IMSB63120/IMSG63120 R0602A Key No. Qty DescriptionExploded Drawing-Model No. IMSB63120/IMSG63120 R0602A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT

IMSG63120, IMSB63120, IMSB63120, IMSG63120 specifications

The Image IMSB63120 and IMSG63120 are highly regarded components in the modern imaging landscape, catering to a diverse range of applications in visual technology. These modules are distinguished by their state-of-the-art features, advanced technologies, and exceptional performance characteristics, making them key players in the industry.

At the core of the IMSB63120 and IMSG63120 modules is their cutting-edge imaging sensor technology. Both models utilize high-resolution image sensors that deliver remarkably clear and detailed images. These sensors offer superior low-light performance, allowing for high-quality image capture even in challenging lighting conditions. This capability makes them ideal for applications ranging from surveillance systems to automotive imaging.

Another notable feature of these models is their fast processing speed. Equipped with advanced image processing algorithms, they can handle complex imaging tasks swiftly and efficiently. This speed is further complemented by real-time processing capabilities, enabling the immediate transmission of image data without compromising quality. This technology is particularly beneficial in scenarios where timely decision-making is critical, such as in security and traffic monitoring systems.

Moreover, the IMSB63120 and IMSG63120 boast a broad dynamic range, which enhances their ability to capture fine details in both bright and dark areas of an image. This characteristic is essential for applications that require accurate color representation and detail capture, such as in medical imaging and broadcasting.

In terms of connectivity, both models offer a variety of interfaces, ensuring compatibility with numerous devices and systems. This flexibility allows for seamless integration into existing workflows, making them versatile options for both professionals and hobbyists alike.

To enhance user experience, the IMSB63120 and IMSG63120 include intuitive user interfaces that facilitate easy operation and customization. Users can adjust various settings according to the specific requirements of their projects, empowering them to achieve the best possible results.

In conclusion, the Image IMSB63120 and IMSG63120 are exemplary imaging solutions that combine high-resolution image capture with advanced processing capabilities. Their robust features, versatility, and performance make them essential tools in a myriad of imaging applications, ensuring they remain at the forefront of technology in their domain.